R
Installation
and Operations
Manual
M9900DVDS
AM / FM / WB and DVD / CD Stereo Receiver
U.S. Patent No. D486,815
Disc Notes
Disc Formats Supported by this Player:
Label side up
I
D
E
O
V
Do not touch
the underside
of the disc
Do not bend
Discs which Cannot be Played with this Player
• DVD-ROM
• DVD-R/DVD-RAM
• CDV
Wipe the disc from center
toward the outside edge
• CD-G
Handling and Cleaning
• Dirt, dust, scratches and warping disc
will cause non operation.
• Do not place stickers on disc or
scratch disc.
• Do not warp discs.
• A disc should always be kept in its case when not
in use to prevent damage.
• Do not place discs in the following places:
Preparing New Discs with Rough Spots
A new disc may have rough edges on its inside
and outside edges. If a disc with rough edges is
used, the proper setting will not be performed and
the player will not play the disc. Therefore, remove
the rough edges in advance by using a ball point
pen or pencil as shown. To do this, press the side
of the pen or pencil against the inside and outside
edges of the disc.
1. Direct sunlight.
2. Dirty, dusty and damp areas.
3. Near car heaters.
4. Car seats or dashboard.
Rough spots on
outside edge
Disc Cleaning
Use a dry soft cloth to wipe the surface. If the disc
is quite dirty, use a soft cloth slightly moist with
isopropyl (rubbing) alcohol. Never use solvents
such as benzine, thinner or conventional record
cleaners as they may mar the surface of the disc.
Ball point pen
or pencil
Note:
A
disc may become somewhat scratched
(although not enough to make it unusable)
depending on handling and conditions in the
usage environment.
Rough spots
on inside edge
3
Radio Button Locations and Functions
20
19
POWER
EJECT
1
18
IR
4 X 50 WATTS
VOLUME
PUSH SEL/
MENU
17
16
15
14
MODE
AS/PS
2
DIM
/ II
LOUD
MUTE
TUNE/TRACK/CH
13
12
PUSH
SCAN/S-MOD/SETUP
EQ
DISP
ENTER
BAND
3
REPEAT
SHUFFLE
INTRO
11
10
W-BND
DISC/CAT
4
5
6
7
8
9
1. Power On/Off: Push to turn the unit on or off.
2. Volume/Sound Controls: Rotate to increase or decrease the volume level. Push to scan between the
different sound controls (Volume, Bass, Treble, Balance and Fader).
3. Multi-Function Knob:
Radio Mode:
Manual Tuning: Rotate the TUNE knob to the left or right and hold until “MANUAL” appears in
the display then release knob. Rotate the TUNE knob again left or right until the desired
radio station appears in the display.
Scan Tuning: Push and release the TUNE knob. The tuner will scan up, pausing for 5 seconds at
each strong station. Push and release the TUNE knob again to cancel the scan function.
Seek Tuning: Rotate the TUNE knob to the left or right and release. The tuner will scan to the
next strong station and stop.
Sirius Satellite Radio Mode: Push to access Manual Tuning, Category Tuning and Direct Tuning in
Sirius mode. (See Sirius Radio Operation for more information, page 15)
DVD Mode: Push to enter DVD Setup Mode (See DVD Setup for more information, page 20)
CD and CD Changer Mode: Rotate the TUNE knob to the left or right to change the CD track on the disc
that is playing.
4. Multi-Function Button #1:
Radio Mode: Push and hold until a beep is heard to memorize a radio station into memory #1. Push
and release when recalling preset radio station #1.
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio station into
memory #1. Push and release when recalling preset radio station #1.
Push the TUNE button first until “CATEGORY” appears in the display then push button 1 to scroll
down through the Sirius Radio playback categories.
CD Changer Mode: Push to change to a lower number disc in the CD changer.
5. Multi-Function Button #2:
Radio Mode: Push and hold until a beep is heard to memorize a radio station into memory #2. Push
and release when recalling preset radio station #2.
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio station into memory
#2. Push and release when recalling preset radio station #2.
Push the TUNE button first until “CATEGORY” appear in the display then push button 2 to scroll up
through the Sirius Radio playback categories.
CD Changer Mode: Push to change to a higher number disc in the CD changer.
4
Radio Button Locations and Functions
6. Multi-Function Button #3:
Radio and Sirius Satellite Radio Modes: Push and hold until a beep is heard to memorize a radio station
into memory #3. Push and release when recalling preset radio station #3.
DVD Mode: Push to select chapter repeat on, title repeat on or repeat off.
CD Mode: Push to repeat a CD track. Push again to cancel.
CD Changer Mode: Push to repeat a CD track. Push again to cancel.
Push and hold to repeat the entire disc. Push again to cancel.
7. Multi-Function Button #4:
Radio and Sirius Satellite Radio Modes: Push and hold until a beep is heard to memorize a radio station
into memory #4. Push and release when recalling preset radio station #4.
CD Mode: Push to play all the tracks on the CD in random order. Push again to cancel.
CD Changer Mode: Push to play all the tracks on the CD in random order. Push again to cancel.
Push and hold to play all the CDs in random order. Push again to cancel.
8. Multi-Function Button #5:
Radio and Sirius Satellite Radio Modes: Push and hold until a beep is heard to memorize a radio station
into memory #5. Push and release when recalling preset radio station #5.
CD Mode: Push to preview each track on the CD for 10 seconds. Push again to cancel.
CD Changer Mode: Push to preview each track on the CD for 10 seconds. Push again to cancel.
Push and hold to preview each track on every CD for 10 seconds. Push again to cancel.
9. Band Button:
Radio Mode: Push to select F1, F2, F3, AM1, AM2 or W (weather band).
Sirius Mode: Push to select SR1, SR2, SR3 or SR4.
10. Weather Band Radio Button: Push to instantly access the weather band radio. Push the MODE button
to return to previous source.
11. Reset Button: Push to restore last programmed settings.
12. Display Button: Push to display the frequency in radio mode, title/chapter in DVD mode or track in CD
mode. Push and hold to perform clock setting functions (See Clock Setting for more information,
page 12).
13. Equalizer Button: Push to choose between preset sound equalization settings.
14. Mute Button (DVD,CD Play/Pause) Button:
Radio and Sirius Satellite Radio Mode: Push to mute volume level. Push again to restore volume.
DVD, CD and CD Changer Mode: Push to pause disc play, push again to resume play.
15. Loud (Dim Button): Push and release to boost high and low tones at low volume levels. Push and hold
to dim or restore backlight of display.
16. AS/PS (DVD and CD Stop Button):
Radio Mode: Push for automatic memory storing and preset scan.
DVD and CD Mode: Push to stop the DVD or CD.
17. Mode Button: Push to change the play source: Radio, Sirius Satellite Radio, DVD/CD, CD Changer or
Auxiliary Sources.
18. Eject Button: Push to eject a DVD/CD.
19. DVD/CD Slot: To play a disc insert a DVD or CD into slot with label facing up.
20. Display Area: This area displays all function information for the radios, clock and DVD/CD players.
5
Remote Control Button Locations and Functions
Inserting the Remote Control Battery:
1. Open the battery compartment.
2. Insert the CR2025 battery. Make
sure that the positive (+) side of
the battery is oriented correctly.
3. Close the battery compartment.
22
23
POWER
EJECT
24
1
W.BAND DISPLAY PROGRAM MUTE
MODE
SUBTITLE ANGLE
ZOOM
2
3
25
26
SHUFFLE REPEAT
A-B
4
5
27
28
29
30
AS PS
RESUME
AUDIO
MENU
BND
SETUP
SCAN
6
7
S-MODE
P
N
31
8
9
OK
32
33
34
TITLE
ST
10
SEL
EQ
11
13
12
14
16
CAT
2
5
8
0
3
1
4
35
36
15
17
Using the Remote Control:
Point the remote control towards the
remote infrared sensor (IR).
VOLUME
DISC
6
18
TUN TRK CH
7
9
37
38
19
20
GOTO
PBC
SLOW
Infrared Sensor
21
1. Power
Push to turn the unit on or off.
2. W.BAND
Push to instantly access the weather band radio. Push the MODE button to return to
previous source.
3. DISPLAY
4. SHUFFLE
Push to display the frequency in radio mode, title/chapter in DVD mode or track in CD
mode. Push and hold to perform clock setting functions (See Clock Setting for more
information, page 12).
CD Mode: Push to play all the tracks on the CD in random order. Push again to cancel.
CD Changer Mode:
Push to play all the tracks on the CD in random order. Push again to cancel.
5. REPEAT
CD Mode: Push to repeat a CD track. Push again to cancel.
CD Changer Mode: Push to repeat a CD track. Push again to cancel.
DVD Mode: Push to select Chapter Repeat On, Title Repeat On or Repeat Off.
6. (AS/PS)
Radio Mode: Push and hold for automatic memory storing. Push and release to scan
preset stations.
DVD Mode: Push to stop the DVD.
7. BND (MENU) Radio Mode: Push to select F1, F2, F3, AM1, AM2 or W (weather band).
Sirius Satellite Radio Mode: Push to select SR1, SR2, SR3, and SR4.
DVD Mode: Push to access the root menu.
8. RESUME
CD Mode: When in stop mode, press this button and play will resume from the stop
point.
9. P/N
10. EQ
DVD Mode: Switches between PAL, NTSC and AUTO modes.
Push to choose between preset sound equalization settings.
6
Remote Control Button Locations and Functions
11. AUDIO
DVD Mode: Changes the audio soundtrack on multi-audio soundtrack DVD disc.
12. ST (TITLE)
Radio Mode:
Mono/Stereo: You can sometimes improve reception of distant stations by selecting mono
operation. Press and release to select mono or stereo mode in FM band only. Stereo
mode is indicated by a ST in the display. Mono mode is indicated by a MON in the display
.
Local/Distant: Local setting is for reception of strong stations, and distant setting is
for reception of weaker stations. This function is in effect during Scan and Seek tuning.
Press and hold to select local or distance mode in FM band only. Local mode
is indicated by a LOC in the display. Distance mode is not indicated in the display.
DVD Mode: Push to display the Title menu that is stored in DVD disc (when available).
13. 3
Radio Mode: Push and hold until a beep is heard to memorize a radio station into
memory #3. Push and release when recalling preset radio station #3.
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio
station into memory #3. Push and release when recalling preset radio station #3.
DVD Mode: Push to select chapter repeat on, title repeat on or repeat off.
CD Mode: Use in conjunction with other numeric buttons to input track number.
CD Changer Mode: Push and release to repeat the track playing on the CD and “RPT” will
appear in the display. Push again to cancel. Push and hold until “DRT” appears in the
display to repeat the disc playing in the changer. Push again to cancel.
14. 1 (CAT
)
)
Radio Mode: Push and hold until a beep is heard to memorize a radio station into
memory #1. Push and release when recalling preset radio station #1.
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio
station into memory #1. Push and release when recalling preset radio station #1.
Push the SCAN button (29) first until “CATEGORY” appears in the display then push
button 1 to scroll down through the Sirius Radio playback categories.
CD Mode: Use in conjunction with other numeric buttons to input track number.
15. 2 (CAT
Radio Mode: Push and hold until a beep is heard to memorize a radio station into
memory #2. Push and release when recalling preset radio station #2.
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio
station into memory #2. Push and release when recalling preset radio station #2.
Push the SCAN button (29) first until “CATEGORY” appear in the display then push
button 2 to scroll up through the Sirius Radio playback categories.
CD Mode: Use in conjunction with other numeric buttons to input track number.
CD Changer Mode: Push and release to scan each track on the CD and “SCN” will
appear in the display. Push again to cancel. Push and hold until “DSN” appears in the
display to scan each track on each disc in the CD Changer. Push again to cancel.
16. 6 (DISC
17. 4
)
CD Mode: Use in conjunction with other numbered buttons to input track number.
CD Changer Mode: Push to change to a higher disc in the CD changer
.
Radio Mode: Push and hold until a beep is heard to memorize a radio station into
memory #4. Push and release when recalling preset radio station #4.
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio
station into memory #4. Push and release when recalling preset radio station #4.
CD Mode: Use in conjunction with other numeric buttons to input track number.
CD Changer Mode: Push and release to play all the tracks on the CD in random order
and “SHF” will appear in the display. Push again to cancel. Push and hold until “DSF”
appears in the display to play all the discs in random order. Push again to cancel.
7
Remote Control Button Locations and Functions
18. 5 (DISC
)
Radio Mode: Push and hold until a beep is heard to memorize a radio station into
memory #5. Push and release when recalling preset radio station #5.
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio
station into memory #5. Push and release when recalling preset radio station #5.
CD Mode: Use in conjunction with other numeric buttons to input track number.
CD Changer Mode: Push to change to a lower disc in the CD changer
.
19. 7, 8, 9, 0
20. GO TO
21. PBC
Use in conjunction with other numeric buttons.
DVD Mode: Goes to bookmark function during DVD playback.
Change between PBC On and PBC Off on VCD discs.
22. PROGRAM CD Mode: Allows the tracks to be played in the order you programmed (See
Programming CD Tracks into Memory, page 13).
23. A-B
24. (EJECT) Push to eject a DVD/CD.
25. MODE Push to change the play source: Radio, Sirius Satellite Radio, DVD/CD, CD Changer or
CD and DVD Modes: Allows a passage to be repeated continuously (CD and DVD).
Auxiliary Sources.
26.
(MUTE) Radio and Sirius Satellite Radio Mode: Push to mute volume level. Push again to
restore volume.
CD and CD Changer Mode: Push to pause disc play, push again to resume play.
DVD Mode: Push to pause movie play, push again to resume play.
27. ANGLE
DVD Mode: Changes the view angle on multi-angle DVD disc.
28. SUBTITLE
DVD Mode: Changes the Subtitle language on multi-subtitle language DVD disc.
29. SCAN
(SETUP)
Radio Mode: Scan Tuning: Push and release the SCAN button. The tuner will scan up,
pausing for 5 seconds at each strong station. Push and release the SCAN button again
to cancel the scan function.
DVD Mode: Push to enter DVD Setup Mode (See DVD Setup for more information, page 20)
Sirius Satellite Radio Mode: Push to access Manual Tuning, Category Tuning and Direct
Tuning. (See Sirius Radio Operation for more information, page 15).
30. ZOOM
DVD Mode: Enlarges or reduces size of picture.
31.
/
Radio Mode: Manual Tuning: Push and hold one of the buttons until “MANUAL” appears in
the display then release button. Push the buttons again up or down until the desired radio
station appears in the display.
DVD Mode: When the menu is displayed these buttons work as navigational buttons.
When a movie is playing these buttons work as Chapter Skip buttons.
32.
/
Radio Mode: Seek Tuning: Push the left or right button and release. The tuner will scan
to the next strong station and stop.
DVD Mode: When the menu is displayed these buttons work as navigational buttons.
When a movie is playing these buttons work as Fast Forward (FF) and Fast Rewind (FR)
buttons.
8
Remote Control Button Locations and Functions
33. OK
DVD Mode: Confirm the Track/Chapter selected with the numeric buttons or selected
with the cursor buttons on screen display.
34. SEL
Push to scan between the different sound controls (Volume, Bass, Treble, Balance and
Fader). Then push VOL +/ to change the setting.
-
35.
36.
-
/ +
Push to increase or decrease the volume level.
VOLUME
/
Radio Mode: Push the left or right button and release. The tuner will scan to the next
TUN/TRK/CH
strong station and stop.
Sirius Satellite Radio Mode: Push the left or right button and release. The tuner will go
to the next station and stop.
CD and CD Changer Mode: Push the left or right button and release to change the
track on the CD that is playing.
DVD Mode: When a movie is playing these buttons work as Chapter Skip buttons.
37.
/
Radio: Push the left or right button until the desired radio station appears in display.
CD and CD Changer Mode: Push and hold the left or right button to Fast Rewind or
Fast Forward the track playing.
DVD Mode: When a movie is playing push
to scroll through Fast Forward (FF 2 X,
to scroll through
FF 4 X, FF 6 X, FF 8 X and PLAY to return to normal). Push
Fast Reverse (FR 2 X, FR 4 X, FR 6 X, FR 8 X and PLAY to return to normal).
38. SLOW
DVD Mode: Push to scroll through Slow Forward (SF 2 X, SF 4 X, SF 8 X) then Slow
Reverse (SR 2 X, SR 4 X, SR 8 X) then normal (PLAY).
9
Basic Operation
POWER
Turning the Unit On and Off: Push the Power button.
Selecting Play Source: Push the Mode button to choose a play source:
Radio, Sirius Satellite Radio (if equipped), CD/DVD, External CD Changer
(if equipped) or Auxiliary Sources (if equipped).
MODE
AS/PS
DIM
/ II
Dimming the Display: Push and hold the LOUD button to dim the backlight
of the display. Push and hold again to return to normal illumination.
LOUD
MUTE
AM/FM Radio Operation
AM/FM Bands: Push BAND button to select a radio band: F1, F2, F3, AM1,
AM2 or W (weather band).
BAND
W-BND
TUNE/TRACK/CH
Manual Tuning:
PUSH
SCAN/S-MOD/SETUP
1. Rotate the TUNE knob left or right and hold until “MANUAL” appears
in the display, then release knob.
2. Rotate the TUNE knob again left or right until the desired radio
station appears in the display.
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
Scan Tuning: Push the TUNE knob to have the radio automatically scan
every 5 seconds for a different radio station. To stop scanning push the
TUNE knob again.
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
Seek Tuning: Rotate the TUNE knob left or right, then release to seek for a
different radio station.
Preset AM/FM Radio Stations
Programming AM/FM Radio Stations: You can program up to 15 FM radio
stations and 10 AM radio stations.
1. Select from F1, F2, F3, AM1 or AM2 by pushing the BAND button
repeatedly.
BAND
W-BND
2. Tune to the desired radio station (see AM/FM Radio Operation above
for more details).
3. Push and hold one of the five STATION RECALL buttons
until a short "beep" is heard. The corresponding preset
button number now appears in the lower right hand
corner of the display.
REPEAT
SHUFFLE
INTRO
4. To program additional preset stations, repeat this procedure using the
other STATION RECALL buttons.
Automatically Programming AM/FM Radio Stations: You can program up to
15 FM radio stations and 10 AM radio stations automatically.
1. Select from F1, F2, F3, AM1 or AM2 by pushing the BAND button
BAND
W-BND
AS/PS
repeatedly.
2. Push and hold AS/PS button until the display starts scanning for a
radio station. The radio will automatically program the 5 strongest
station into preset memory.
MODE
10
(continued)
Preset AM/FM Radio Stations
Recalling AM/FM Radio Stations:
BAND
W-BND
1. Select from F1, F2, F3, AM1 or AM2 by pushing the BAND button
repeatedly.
2. Push button 1, 2, 3, 4 or 5 to recall a preprogrammed radio
station.
REPEAT
SHUFFLE
INTRO
Automatically Recalling AM/FM Radio Stations:
BAND
MODE
W-BND
AS/PS
1. Select from F1, F2, F3, AM1 or AM2 by pushing the BAND button
repeatedly.
2. Push the AS/PS button and release to automatically scan every 5 seconds
the through preprogrammed radio stations. To stop scanning push the
AS/PS button again.
Weather Band Radio Operation
Weather Band: Push the W-BND button to immediately access the weather
band. The radio will search for the strongest weather band signal in your area.
BAND
W-BND
PUSH
TUNE/TRACK/CH
SCAN/S-MOD/SETUP
S
can Tuning: Push the TUNE knob to scan every 5 seconds through all 7
weather band stations. To stop scanning push the TUNE knob again.
TUNE/TRACK/CH
Manual Tuning:
PUSH
SCAN/S-MOD/SETUP
1. Rotate the TUNE knob left or right and hold until “MANUAL” appears
in the display, then release knob.
2. Rotate the TUNE knob again left or right until the desired weather
band radio station appears in the display.
Directly Recalling Weather Band Radio Stations:
1. Push button 1, 2, 3, 4 or 5 to directly recall weather
band station 1 thru 5.
REPEAT
SHUFFLE
INTRO
Sound Controls
VOLUME
PUSH SEL/
MENU
Volume Control: Rotate the VOLUME knob to the right to increase levels or
left to decrease levels.
Bass, Treble, Balance and Fader Controls: Push and release the VOLUME knob
to scan between the different sound controls. Once the desired function is in
the display area rotate the knob left or right to achieve the desired level.
VOLUME
PUSH SEL/
MENU
Bass Control: The bass control adjusts the amount of low frequency that
you hear.
4
X
50 WATTS
H
NU
SEL/
LOC
Treble Control: The treble control adjusts the amount of high frequency
that you hear.
USH
VOLUME
Balance Control: The balance control adjusts the amount of sound output
to the left and right speakers.
PUSH SEL/
MENU
Fader Control: The fader control adjusts the amount of sound output to
the front and rear speakers.
11
(continued)
Sound Controls
Equalizer: Push the EQ button to choose between preset equalizer settings:
Classic, Rock, DSP Off (digital sound processor off), Flat, Pop and Jazz,
as indicated in the display area.
EQ
DISP
DIM
/ II
MUTE
Mute (DVD, CD Play/Pause) Button: Push the MUTE button to mute the
radio volume. If a DVD or CD is playing the MUTE button will pause the
disc. Push the MUTE button again to restore the volume or resume play-
ing the disc.
LOUD
Loudness: Push the LOUD button to boost high and low tones at low
volume levels.
LOUD
MUTE
Clock Setting
Display Button: Push and hold the DISP button until the clock is flashing in
EQ
DISP
PUSH
the display.
TUNE/TRACK/CH
Adjusting the Minutes: Rotate the TUNE knob to the Left to adjust the Minutes.
SCAN/S-MOD/SETUP
Adjusting the Hours: Rotate the TUNE knob to the Right to adjust the Hours.
Note: the AM/PM indicators.
When correct time displays wait a few seconds to allow the time to program.
Minutes
Hours
CD Operation
Playing a CD: Insert a CD (label side up) into the CD slot. The CD will
auto-load and start playing.
Note: If a CD does not auto-load DO NOT FORCE IT into the slot, as you
may already have a disc loaded.
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
CD Track Selection: Rotate the TUNE knob left or right to change the track.
The track number will appear in the display.
DIM
/ II
Pausing a CD: Push the MUTE button to “Pause” the disc, push again to
resume play.
LOUD
MUTE
EJECT
Ejecting a CD: Push the EJECT button to to eject a disc.
Repeating a CD Track: Select the desired track to repeat then push the
REPEAT button until “S-RPT” appears in the display. That track will play
repeatedly. To cancel this feature push the REPEAT button until “S-RPT” dis-
appears from the display.
REPEAT
Random CD Track Play Order: Push the SHUFFLE button until “S-SHF” appears
in the display. The tracks on the disc will play in a random order. To cancel this
feature push the SHUFFLE button until “S-SHF” disappears from the display.
SHUFFLE
Preview CD Tracks: Push the INTRO button until “S-SCN” appears in the
display. Each track on the disc will play for 10 seconds. To cancel this
feature push the INTRO button until “S-SCN” disappears from the display.
INTRO
12
(continued)
CD Operation
Elapse Times: Push the AS/PS button to display running time of CD track,
push the button again to display the time remaining on the CD track, push
one more time to display time remaining on CD.
MODE
AS/PS
AS PS
Programming CD Tracks into Memory (Using the Remote Control):
1. In CD mode, push the AS/PS button on the remote control
.
PROGRAM
2. Push the PROGRAM button and P00-0000 will appear in the display.
CAT
2
5
3
1
4
7
3. Push the Numeric buttons to select the first track to be programmed
into memory. For example: push numeric button 4, “P01-004” appears
in the display indicating that track 4 will be played first.
DISC
6
9
8
0
4. Repeat Step 3 to store up to 99 tracks into memory.
MUTE
5. Push the
MUTE button to play tracks in programmed order.
Canceling Programmed CD Tracks:
1. Push the AS/PS button
AS PS
.
PROGRAM
MUTE
2. Push the PROGRAM button.
3. Push the
MUTE button to resume normal play.
13
CD Changer Operation
Loading CDs: Load CDs into the CD magazine and insert the magazine into
the external CD changer
Selecting the External CD Changer: Push the MODE button until “CDC”
MODE
AS/PS
appears in the display.
CD Selection: Push button 1 or 2 to scroll through the selection of CDs in the
CD changer. If a CD is not in one of the trays, the unit will continue until the
next CD is found.
DISC/CAT
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
CD Track Selection: Rotate the TUNE knob left or right to change the track.
The track number will appear in the display.
Repeating a CD Track: Select the desired track to repeat then push and
release the REPEAT button until “RPT” appears in the display. The track
on the disc will play repeatedly. To cancel this feature push the REPEAT
button until “RPT” disappears in the display.
REPEAT
Repeating a CD: Select the desired CD to repeat then push and hold the
REPEAT button until “DPT” appears in the display. The entire disc will
play repeatedly. To cancel this feature push the REPEAT button until
“DPT” disappears from the display.
Random CD Track Play Order: Push and release the SHUFFLE button until
“SHF” appears in the display. The tracks on the disc will play in a random
order. To cancel this feature push the SHUFFLE button until “SHF”
disappears from the display.
SHUFFLE
Random CD Play Order: Push and hold the SHUFFLE button until “DSF”
appears in the display. The discs will play in a random order. To cancel this
feature push the SHUFFLE button until “DSF” disappears from the display.
Preview CD Tracks: Push and release the INTRO button until “SCN” appears
in the display. Each track on the disc will play for 10 seconds. To cancel
this feature push the INTRO button until “SCN” disappears from the display.
INTRO
Preview CDs: Push and hold the INTRO button until “DSN” appears in the
display. Each track on every disc will play for 10 seconds. To cancel this
feature push the INTRO button until “DSN” disappears from the display.
14
Sirius Satellite Radio Setup
Note: If your Sirius tuner is not activated, call 1-888-539-SIRIUS to activate. The Sirius Tuner ID Number
(ESN) is required during the activation process. Following the instructions below to access the Sirius
Tuner ID Number (ESN):
Accessing you Sirius Tuner ID Number (ESN):
MODE
AS/PS
1. Push the MODE button until “SIRIUS” appears in the display area.
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
2. Push the TUNE button until “DIRECT” appears in the display area. Wait a
few seconds and “CH 000” will then appear in the display.
3. Push the BAND button and the first 4 digits of the 12 digit Sirius Tuner ID
Number (ESN) will be displayed.
BAND
W-BND
4. Push the DISP button and the last 8 digits of your 12 digit Sirius Tuner
ID Number (ESN) will be displayed.
EQ
DISP
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
5. Push the TUNE button to exit.
Sirius Satellite Radio Operation
Please note that satellite radio signal may be blocked by trees, buildings, bridges or tunnels.
Selecting Sirius Satellite Radio: Push the MODE button until “SIRIUS”
MODE
AS/PS
appears in the display. Please be patient as it may take a minute to receive a
satellite signal.
TUNE/TRACK/CH
Manual Tuning:
PUSH
SCAN/S-MOD/SETUP
1. Push the TUNE knob until “NORMAL” appears in the display.
2. Rotate the TUNE knob to select a station from 01-182.
TUNE/TRACK/CH
Category Tuning:
PUSH
SCAN/S-MOD/SETUP
1. Push the TUNE knob until “CATEGORY” appears in the display.
2. Push button 1 or 2 to find the desired category.
DISC/CAT
TUNE/TRACK/CH
3. Rotate the TUNE knob and select a station within the category.
PUSH
SCAN/S-MOD/SETUP
15
Sirius Satellite Radio Operation (Continued)
TUNE/TRACK/CH
Direct Tuning:
PUSH
SCAN/S-MOD/SETUP
1. Push the TUNE knob until “DIRECT” appears in the display.
2. Rotate the TUNE knob and select the first digit (0 or 1).
3. Push the TUNE knob again.
4. Rotate the TUNE knob and select the second digit (1-8).
5. Push the TUNE knob again.
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
6. Rotate the TUNE knob and select the third digit (1-9). The tuner will
start playing the station you have selected when the third digit stops
flashing.
Preset Sirius Satellite Radio Stations
Programming Satellite Radio Stations: You can program up to 20 Sirius
Satellite radio stations.
1. Select from SR1, SR2, SR3 or SR4 by pushing the BAND button
repeatedly.
BAND
W-BND
2. Tune to the desired radio station (see Sirius Satellite Radio Operation
for more details).
3. Push and hold one of the five STATION RECALL buttons
until a short "beep" is heard. The corresponding preset
button number now appears in the lower right hand
corner of the display.
REPEAT
SHUFFLE
INTRO
4. To program additional preset stations, repeat this procedure using the
other STATION RECALL buttons as desired.
Recalling Satellite Radio Stations:
BAND
W-BND
1. Select from SR1, SR2, SR3 or SR4 by pushing the BAND button
repeatedly.
2. Push button 1, 2, 3, 4 or 5 to recall a preprogrammed radio
station.
REPEAT
SHUFFLE
INTRO
Automatically Recalling Satellite Radio Stations:
BAND
MODE
W-BND
AS/PS
1. Select from SR1, SR2, SR3 or SR4 by pushing the BAND button
repeatedly.
2. Push AS/PS button and release to automatically scan every 5 seconds
the pre-programmed radio stations. To stop scanning push the AS/PS
button again.
16
Channel Skip Sirius Satellite Radio
Programming Channel Skip for Satellite Radio Stations: You can program
the radio to skip channels which you do not want.
1. Tune to the station to be skipped (see Sirius Satellite Radio Operation
for more details).
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
2. Push the TUNE knob until “SET SKIP” appears in the display.
ENTER
BAND
3. Push the BAND button and “SKIP” will appear flashing in the bottom of
the display. When the “SKIP” stops flashing the channel has been pro-
grammed to skip.
W-BND
TUNE/TRACK/CH
Release Channel Skip for Satellite Radio Stations:
PUSH
SCAN/S-MOD/SETUP
1. Push the TUNE knob until “DIRECT” appears in the display.
2. Rotate the TUNE knob and select the first digit of the skipped channel
(0 or 1).
3. Push the TUNE knob again.
TUNE/TRACK/CH
4. Rotate the TUNE knob and select the second digit of the skipped channel
(1-8).
PUSH
SCAN/S-MOD/SETUP
5. Push the TUNE knob again.
6. Rotate the TUNE knob and select the third digit of the skipped channel
(1-9). The tuner will start playing the station you have selected when the
third digit stops flashing.
TUNE/TRACK/CH
PUSH
SCAN/S-MOD/SETUP
7. Push the TUNE knob until “SET SKIP” appears in the display. After a few
seconds the radio channel will appear in the display with “SKIP”
flashing at the bottom.
ENTER
BAND
8. Push the BAND button and “SKIP” will stop flashing in the bottom of the
display. When the “SKIP” disappears the channel has been released from
Channel Skip.
W-BND
Auxiliary Input
Selecting Auxiliary Input: Push the MODE button until “AV IN1” or “AV IN2”
appears in the display which indicates that the auxiliary unit is playing
through the M9900DVDS.
MODE
AS/PS
Note: All sound controls (pages 11-12) are active when the Auxiliary
source is playing.
17
DVD Operation
Playing a DVD: Insert a DVD (label side up) into the DVD slot.
Note: If a DVD does not auto-load DO NOT FORCE into the slot, as you
may already have a CD or DVD loaded.
1. The DVD will start playback automatically and stop at the menu display.
OK
2. Use the Navigation
highlighted bar in the menu.
buttons on the remote to move the
/
,
/
OK
3. Press OK button on the remote to confirm selection.
Stopping a DVD: Push the AS/PS button to stop the unit playback, when the
MUTE button is pressed, normal playback will continue.
AS PS
Push the AS/PS button twice to stop the playback and go back to initial
Chapter.
MUTE
Pausing a DVD: Push the
MUTE button to “Pause” the disc, push it again
to resume play.
EJECT
Ejecting a DVD: Push the EJECT button to eject a disc.
Previous Chapter Next Chapter
Chapter Skip: Push the
button to skip forward to the next chapter. Push
the
button to skip backwards to the previous chapter.
TUN TRK CH
Fast Reverse/Fast Forward: Push the
or
buttons to fast reverse or fast
Fast Reverse
Fast Forward
forward during play. Each time the button is pressed the speed changes.
2X
4X
6X
8X
Normal Playback
Slow Motion Forward/Reverse: Push the SLOW button to scroll through Slow
Forward (SF 2X, SF 4X, SF 8x) then Slow Reverse (SR 2X, SR 4X, SR 8x)
then normal (PLAY).
SLOW
SF 2X
SF 4X
SF 8X
SR 2X
SR 4X
SR 8X
Normal Playback
Repeat Play: Push the REPEAT button to scroll through Chapter Repeat On,
Title Repeat On and Repeat Off.
REPEAT
Chapter Repeat On
Title Repeat On
Repeat Off
Passage Repeat: Allows a passage to be repeated continuously.
1. Push the A-B button at the start of the required passage.
2. Push the A-B button at the end of the passage. The unit will repeat playing
the passage set from A to B.
A-B
Cancelling Passage Repeat. To revert to normal play push the A-B button again.
18
DVD Operation (continued)
GO TO Title/Chapter Select Function: To directly select a Title/Chapter follow
these directions:
GOTO
1. Push the GO TO button and the screen will display the TITLE and
CHAPTER information.
CAT
1
4
7
2
3
6
9
DISC
5
2. Use the Numeric buttons to input the Title/Chapter number.
3. Push the OK button to execute the GO TO function.
8
0
OK
GOTO
GO TO Time Select Function: To directly select a time in the DVD follow these
X2
directions:
1. Push the GO TO button TWICE and the screen will display the TITLE and
TIME information.
CAT
1
2
3
DISC
4
7
5
6
9
2. Use the Numeric buttons to input the Time.
8
0
OK
3. Push the OK button to execute the GO TO function.
DVD Disc Information: Push the DISPLAY button to scroll through playback to
display the console information of the current disc onscreen.
DISPLAY
TITLE/CHAPTER
TITLE REMAIN
CHAPTER ELAPSE
CHAPTER REMAIN
Off
PAL/NTSC System Selection: Press the P/N button to switch between PAL,
NTSC and AUTO modes.
P
N
Note: This function is only effective when the DVD logo is displayed or when
disc play is stopped.
Audio Languages Function: Push the AUDIO button during playback. Each
time the button is pressed, the audio soundtrack language changes in
sequential order.
AUDIO
Notes:
• The language number maybe different according to the disc.
• Some discs only contain one language soundtrack.
• When no different language soundtracks are recorded, will be displayed
in the top left corner of the screen.
Subtitle Languages Function: Push the SUBTITLE button during playback. Each
time the button is pressed, the subtitle language changes in sequential order.
Notes:
SUBTITLE
• The language number maybe different according to the disc.
• Some discs only contain one subtitle language.
• When no different language soundtracks are recorded, will be displayed
in the top left corner of the screen.
19
DVD Operation
Angle Function: Push the ANGLE button during playback. Each time the button
is pressed, the angle changes in sequential order.
Notes:
ANGLE
• The angle number maybe different according to the disc.
• The function only works for discs having scenes recorded at different
angles.
• When no different angles are recorded, will be displayed in the top left
corner of the screen.
Zoom Function: Allows the picture to be increased in size. Push the ZOOM
button during playback. Each time the button is pressed, the zoom changes
in sequential order.
ZOOM
Zoom X 1.5
Zoom X 2
Zoom X 3
Zoom Off
Note: During ZOOM mode, press the
/
,
/
buttons to move picture left,
right, up or down.
DVD Setup
Initial Setup
General Setup
- - GENERAL PAGE - -
SETUP MENU -- MAIN PAGE
TV DISPLAY
PIC MODE
NORMAL /PS
NORMAL /LB
WIDE
GENERAL SETUP
AUDIO SETUP
ANGLE MARK
OSD LANG
PREFERENCES
CAPTIONS
EXIT SETUP
SCREEN SAVER
MAIN PAGE
SETUP
SCAN
1. Press SCAN/SETUP and the Initial
Setup Menu is displayed.
TV DISPLAY Setup: This is to select the appropriate
TV aspect ratio (4:3 or 16:9) according to the
connected TV set.
2. Select the preferred item by using
the
buttons.
/
,
/
OK
NORMAL /PS (For 4:3 TV): Played back in PAN
and SCAN style (If connected to wide-screen
TV, the left and right edges are cut off).
3. Push OK button to enter selected
menu.
Menus
NORMAL /LB (For 4:3 TV) Played back in letter
box style (If connected to wide-screen TV,
black bands appear at top and bottom of the
screen).
General Setup: This setup page includes all the
items of TV display and Audio output features.
(See General Setup Menu for more information)
Audio Setup: This setup page includes all the
items for Audio. (See Audio Setup Menu for
more information)
WIDE (For 16:9 TV): Select when a wide-screen
TV set is connected.
Preferences Setup: This setup page includes all
the support features. (See Preferences Setup
Menu for more information)
20
DVD Setup
- - GENERAL PAGE - -
TV DISPLAY
- - GENERAL PAGE - -
TV DISPLAY
PIC MODE
PIC MODE
ANGLE MARK
OSD LANG
AUTO
HI-RES
ANGLE MARK
OSD LANG
NON-FLICKER
CAPTIONS
CAPTIONS
SCREEN SAVER
MAIN PAGE
ON
SCREEN SAVER
MAIN PAGE
OFF
PIC Setup: Select AUTO, the player PIC mode will
depend on DVD disc. Select HI-RES format for
best image resolution. Select NON-FLICKER format
on image or picture with noise or distortion.
SCREENSAVER Setup: Select the SCREENSAVER ON
or OFF.
Audio Setup
- - AUDIO PAGE - -
- - GENERAL PAGE - -
LPCM OUTPUT
MAIN PAGE
LPCM 48K
LPCM 96K
TV DISPLAY
PIC MODE
ANGLE MARK
OSD LANG
ON
OFF
LPCM Setup: Select the LPCM (Line Pulse Code
Modulation) OUTPUT between LPCM 48K and
LPCM 96K. The higher the sampling frequency is,
the better the output audio quality will be. It is rec-
ommended to select LPCM 96K compression.
CAPTIONS
SCREEN SAVER
MAIN PAGE
ANGLE MARK Display Setup: If it is set ON, when a
multi-angle DVD disc is playing, “ “ (the angle
mark) will appear on the screen. If it is set to
“OFF” the mark will not appear.
Preferences Setup
- - PREFERENCES - -
TV TYPE
AUDIO
AUTO
NTSC
PAL
- - GENERAL PAGE - -
TV DISPLAY
PIC MODE
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULTS
MAIN PAGE
ANGLE MARK
OSD LANG
CAPTIONS
ENGLISH
FRENCH
GERMAN
SPANISH
SCREEN SAVER
MAIN PAGE
TV TYPE Setup: This play can play discs recorded in
either PAL or NTSC format. Select NTSC format,
when the unit is connected to a NTSC TV. Select
PAL format, when the unit is connected to a PAL
TV. Select AUTO format, the player TV output for-
mat will be according to the DVD disc format.
OSD LANG (On-Screen Language Display) Setup:
Select the preferred On-Screen Display language
by using the
buttons.
,
/
- - GENERAL PAGE - -
TV DISPLAY
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
ON
SCREEN SAVER
MAIN PAGE
OFF
Captions Setup: When playing DVD disc, activate the
CAPTIONS feature by selecting ON and the cap-
tions (such as the actor dialogue) appear on the
screen. Deactivate this feature by selecting OFF
and the caption will appear.
21
DVD Setup
Preferences Setup
- - PREFERENCES - -
TV TYPE
- - PREFERENCES - -
AUDIO
TV TYPE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULTS
MAIN PAGE
ENGLISH
FRENCH
SPANISH
CHINESE
JAPANESE
GERMAN
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULTS
MAIN PAGE
CHANGE
PASSWORD Setup: Select CHANGE and press the OK
button. Type the old password (The initial factory
code is 3308) then key-in a new 4-character pass-
word. Then retype it again to confirm new pass-
word.
AUDIO Setup: Select the preferred AUDIO language
by using the cursor buttons.
- - PREFERENCES - -
TV TYPE
- - PREFERENCES - -
ENGLISH
FRENCH
SPANISH
CHINESE
JAPANESE
GERMAN
OFF
AUDIO
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULTS
MAIN PAGE
TV TYPE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULTS
MAIN PAGE
RESET
SUBTITLE Setup: Select the preferred SUBTITLE
language by using the cursor buttons.
DEFAULTS: Select reset to revert to factory initial
settings.
- - PREFERENCES - -
TV TYPE
AUDIO
DEFAULT SETTINGS
GENERAL SETUP TV DISPLAY
PIC MODE
NORMAL/PS
AUTO
ON
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULTS
MAIN PAGE
ENGLISH
FRENCH
SPANISH
CHINESE
JAPANESE
GERMAN
ANGLE MARK
OSD LANGUAGE ENGLISH
CAPTIONS
SCREENSAVER
LPCM OUTPUT
TV TYPE
OFF
OFF
LPCM 96K
AUTO
DISC MENU Setup: Select the preferred DISC MENU
language by using the cursor buttons.
AUDIO SETUP
PREFERENCES
AUDIO
ENGLISH
ENGLISH
ENGLISH
6PG-R
3308
- - PREFERENCES - -
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULT
TV TYPE
AUDIO
1 G
2
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULTS
MAIN PAGE
3 PG
4 PG13
5
RESET
6 PG-R
7 NC-17
8 ADULT
PARENTAL Setup: Select a suitable parental guidance
by the cursor buttons and confirm by pressing the
OK button.
22
Speciality Features
Display Button: The factory default setting is clock display priority. Push the
DISPLAY button at any time to display the radio frequency, CD track, AUX
1 or AUX 2.
EQ
DISP
Note: In the Sirius mode the factory default setting is Sirius channel
display priority. Push the DISPLAY button at any time to display the
CN-NAME, SONG TITLE, ARTIST, CATEGORY and Clock. If clock is cho-
sen the time will be displayed for approximately 5 seconds then revert to
displaying the Category.
Restoring Factory Default Setting: To restore the radio to the factory default
MODE
AS/PS
W-BND
setting:
1. Press the MODE button to select the radio band
.
ENTER
BAND
2. Push the BAND button and and hold until “EEP INIT” appears in the
display. All settings will be restored to the factory default.
Reset Button: The radio panel or LCD display may fail to function normally
due to the vehicle’s battery condition, and may require resetting the radio
microprocessor if:
• The vehicle has been “jump started” from a dead battery condition.
• The vehicle battery becomes very low and is quick-charged.
• The vehicle battery is removed and replaced.
Should this condition occur, simply press and release the RESET button
on the radio panel using the tip of a ball point pen. This will reset the
radio microprocessor to the original factory settings. After pressing the
RESET button you should recheck to see if the radio functions normally.
All station programming should remain, but you will have to reset the
clock. Should the LCD display area show any abnormal error code, please
refer to the trouble shooting guide and solution chart below.
Error Code Problem
Description
Possible Remedy
ERR 1
Mechanism Problem Unknown mechanical
problem with the CD
1. Eject the disc and try another.
2. Press the reset button.
3. Replace the unit.
mechanism.
ERR 2
TOC Reading Error
Laser can not read the
CD disc table of
contents.
1. Insert a different disc.
2. Check disc for excessive scratches.
3. Check disc for dirt and fingerprints.
Clean disc and reinsert.
ERR 3
ERR 4
Error from High
Ambient Temp.
The temperature of the Reduce the temperature inside the vehicle
mechanism is too high and try to play a CD at a later time.
to play CDs without
damaging them.
DVD Error
Disc Error
Error during playback
of disc.
1. Insert a different disc.
2. Check disc for excessive scratches.
3. Check disc for dirt and fingerprints.
Clean disc and reinsert.
4. Press the reset button.
ERR 5
Error during eject
and loading disc.
1. Push the reset button.
2. Replace the unit.
23
Changing the Default Settings
The M9900DVDS has a small group of settings that can be changed to suit your personalized requirement.
VOLUME
Button Confirmation Beep: The factory default setting is BEEP ON (a
confirmation beep every time a button or knob is pushed). To turn the beeps
off, push and hold the VOLUME knob until “BEEP ON” is in the display then
release. Rotate the VOLUME knob until “BEEP OFF” is in the display. Wait a
few seconds, the radio will return to last radio mode selected.
PUSH SEL/
MENU
Power Up Volume Level: The factory default setting for initial power-up volume
level is 12. To change the initial volume level, push and hold the VOLUME
knob until “BEEP ON” is in the display then release. Push the VOLUME knob
until “P-VOL” is in the display. Rotate the VOLUME knob until the desired
initial volume is achieved. Wait a few seconds, the radio will return to last
radio mode selected.
VOLUME
PUSH SEL/
MENU
Radio Frequency Display: The factory default setting is USA. Do not change this
setting.
Clock Display When the Radio is Off: When the ignition key is on and the radio
is off, “clock display on” is the default setting. To change the setting to “clock
display off”, push and hold the VOLUME knob until “BEEP ON” is in the
display then release. Push the VOLUME knob until “CLK ON” is in the display.
Rotate the VOLUME knob until “CLK OFF” is in the display. Wait a few
seconds, the radio will return to last radio mode selected.
VOLUME
PUSH SEL/
MENU
Display Priority: The factory default setting for display priority is “CLOCK”
except in Sirius mode. To change the display priority (either radio frequency
priority or no priority), push and hold the VOLUME knob until “BEEP ON” is in
the display then release. Push the VOLUME knob until “CLOCK” is in the
display. Rotate the VOLUME knob until “FREQ” or “NO PRI” is in the display.
Wait a few seconds, the radio will return to last radio mode selected.
VOLUME
PUSH SEL/
MENU
VOLUME
Clock Type, 12 hour or 24 hour: The factory default setting is 12 hour clock with
AM and PM indication. To change the clock type to 24 hour military time,
push and hold the VOLUME knob until “BEEP ON” is in the display then
release. Push the VOLUME knob until “12 HOUR” is in the display. Rotate the
VOLUME knob until “24 HOUR” is in the display. Wait a few seconds, the
radio will return to last radio mode selected.
PUSH SEL/
MENU
24
Installation
White Wire with Black Stripe: Connect this wire to
the Left Front Speaker (-) negative terminal or wire.
S
tep 1: The radio chassis is designed to be “Sleeve
Mounted” through a opening in the dashboard panel.
The required opening size is 182mm (7-3/16") x
84mm (3-5/16"). Cut or engage an opening in the
dashboard to accommodate the mounting sleeve.
Green Wire with Black Stripe: Connect this wire to
the Left Rear Speaker (-) negative terminal or wire.
Green Wire: Connect this wire to the Left Rear
Speaker (+) positive terminal or wire.
Step 2: Insert the mounting sleeve into the hole
in the dashboard. Bend the metal tabs on the
sleeve to secure the mounting sleeve to the dash-
board.
Gray Wire: Connect this wire to the Right Front
Speaker (+) positive terminal or wire.
Gray Wire with Black Stripe: Connect this wire to the
Right Front Speaker (-) negative terminal or wire.
Step 3: Bring all wiring for the connection of the
unit (including the antenna) through the center of
the mounting sleeve. Connect the wiring as follows:
Purple Wire with Black Stripe: Connect this wire to
the Right Rear Speaker (-) negative terminal or wire.
Yellow Wire (w/Fuse): Connect this wire to a
constant +12 volt power source (a power source
that is not controlled by the ignition key).
Purple Wire: Connect this wire to the Right Rear
Speaker (+) positive terminal or wire.
Note: This unit is designed to connect to (4) four
speakers. If the installation only requires (2) two
speakers, use the White and Gray wire sets to
connect the speakers.
Red Wire: Connect this wire to a switched +12 volt
power source (a power source turned on and off
by the ignition key).
Blue Wire: Connect this wire to the (+) power
antenna activation circuit. If no power antenna
exists, tape-off the end of this wire to prevent
shorting out the unit.
WARNING! Any wires left unconnected must
be taped-off or capped off to prevent shorting.
DO NOT connect speaker ground wires together.
DO NOT connect speaker ground wires to the
chassis of the vehicle.
Black Wire: Connect this wire to the frame of the
vehicle (ground). This wire is the chassis grounding
wire for the unit.
DO NOT connect front and rear speaker wires
together.
White Wire: Connect this wire to the Left Front
Speaker (+) positive terminal or wire.
FAILURE TO FOLLOW ANY OF THESE WARNINGS
WILL RESULT IN DAMAGE TO THIS UNIT AND
VOIDS THE WARRANTY.
Sheet
Metal
Screw
Nut
Washer
POWER
VOLUME
PUSH SEL/
MENU
Metal Strap
Dashboard
TUNE/TRACK
LO
C
SCAN/SHIFT
ME
EJECT
M
OR
Y
PRO2
G
RA
M
ELAPSE
MO
D
D
3
REPE
AS
/
AT
IM
PS
4
LOU
S
H
/
II
D
U
FF
LE
MU
DI
T
5
SC
EQ
A
N
S
P
BA
N
D
W-
B
Mounting Sleeve
AN
25
Connection
Right
Front Speaker
Right
Rear Speaker
-
+
+
-
Purple Wire: Rear Right Speaker (+)
Purple/Black Wire: Rear Right Speaker (-)
Gray/Black Wire: Front Right Speaker (-)
Gray Wire: Front Right Speaker (+)
Green Wire: Rear Left Speaker (+)
Green/Black Wire: Rear Left Speaker (-)
White/Black Wire: Front Left Speaker (-)
White Wire: Front Left Speaker (+)
-
+
+
-
Black Wire: Ground
Blue Wire: Power Antenna
Red Wire: Ignition Switched 12 VDC
Left
Front Speaker
Left
Rear Speaker
1 AMP
Yellow Wire: 12 VDC Constant
Auxiliary Input 1 (Yellow Cable)
Audio/Video Output
Red (Audio In / Right)
White (Audio In / Left)
Yellow (Video In)
VCR
or
TV
or
DVD
M9900DVDS
or
Auxiliary Input 2 (Black Cable)
Red (Audio In / Right)
Video
Game
White (Audio In / Left)
Yellow (Video In)
Audio Amplifier
Audio/Video Output (Gray Cable)
Red (Audio Out / Right)
See Amplifier Instructions
for Proper Connections
White (Audio Out / Left)
Monitor
Yellow (Video Out)
26
Sirius Tuner Connection (Optional)
M9900DVDS
M9SIR
Sirius Satellite Antenna
Male/Male Mini Din
(Supplied with Sirius Tuner)
CD Changer Connection (Optional)
Male/Male
(Supplied with
External
CD Changer)
External CD Changer
M9900DVDS
Remote IR Sensor Connection (Optional)
Remote IR Sensor
(Mounted In-Dash)
M9900DVDS
27
Antenna Connection
M9900DVDS
Antenna
28
Trouble Shooting
If it appears that your DVD unit is faulty, first consult
the checklist below. It may be that something simple
has been overlooked. Under no circumstance should
you try to repair the player yourself, as this will
invalidate the warranty. Only qualified service person-
nel should remove the cover or service this player.
The Player Does Not Respond to the Remote
Control:
• Aim the remote control directly at the infrared
sensor on the front of the player.
• Avoid all obstacles which may interfere with the
signal path.
No Power:
• Inspect or replace the remote control battery.
• If the power supply is connected to the car
accessory circuits, but the engine is not run-
ning, switch the ignition key to “ACC”.
Distorted or B/W Picture:
• The disc format is not set according to the TV
• Check if the fuse is blown. If so, replace it with
a new fuse of the same value.
set used (PAL/NTSC).
Buttons Do Not Work:
• Press the RESET button on the front panel of
• Check if the Power On/Off button is set to on.
the radio.
No Picture:
• Check if the monitor or TV is switched on.
The Radio Does Not Work:
• Check if DVD mode is selected.
• Check the video connection.
• Check if the antenna cable is properly connected.
The Radio Station Automatic Selection Does Not
Work:
Distorted Picture:
• The signals maybe too weak, select a station
manually.
• Check the disc for debris and clean with soft
cloth, wiping from the center to the edge.
• Sometimes a small amount of picture distortion
may appear. This is not a malfunction.
Completely Distorted Picture:
• The disc format is not set according to the TV
set used (PAL/NTSC).
No Color in Picture:
• The disc format is not set according to the TV
set used (PAL/NTSC).
Disc Does Not Play:
• Ensure that the disc was inserted label up.
• Clean the disc.
• Check if the disc is defective by trying another
disc.
29
Order-By-Mail Replacement Parts
DESCRIPTION
MODEL #
PRICE
POWER
EJECT
MODE
W.BAND DISPLAY PROGRAM MUTE
SHUFFLE REPEAT
A-B
SUBTITLE ANGLE
ZOOM
AS PS
RESUME
AUDIO
MENU
BND
SETUP
SCAN
S-MODE
P
N
OK
M9900DVDS Remote Control
RC9900DVD
$39.95 ea.
TITLE
ST
EQ
SEL
CAT
1
4
2
5
8
0
3
VOLUME
DISC
6
TUN TRK CH
7
9
GOTO
PBC
SLOW
Specifications
General:
Power Supply Requirements:
Chassis Dimensions:
Tone Controls
DC 12 Volts, Negative Ground
180mm (W) x 160mm (D) x 80mm (H)
Bass (at 100 Hz)
10 dB
Treble (at 10 kHz)
Maximum Output Power
Current Drain
10 dB
4 x 40 Watts
15 Ampere (max.)
CD Player:
Signal to Noise Ratio:
Channel Separation:
Frequency Response:
More than 55 dB
More than 45 dB
20Hz - 20kHz
Radio:
FM
Frequency Coverage:
IF
87.5 to 107.9 MHz
10.7MHz
Sensitivity (S/N = 30dB)
Stereo Separation
12 dBu
> 25 dB
AM
Frequency Coverage:
IF
530 to 1720 kHz
450 kHz
Sensitivity (S/N = 20dB)
36 dBu
WB
Frequency Coverage:
IF
162.40 to 162.55 MHz
10.7MHz
Sensitivity (S/N = 30dB)
15 dBu
Note: Due to improvement in technology, specifications and design are subject to change without notice.
30
Replacement Parts Order Form
Send Orders To: Magnadyne Corporation
We Accept Checks, Money Orders, Visa and Master Card
ATTN: Consumer Parts Sales
Make Checks Payable to: Magnadyne Corporation
P.O. Box 5365
Carson, CA 90749-5365
SHIP TO: (No P.O. Boxes)
LAST NAME
FIRST NAME
INITIAL
STREET ADDRESS (IF PAYING WITH A CREDIT CARD, YOUR BILLING ADDRESS IS REQUIRED)
CITY
STATE
ZIP CODE
DAYTIME PHONE NUMBER
CREDIT CARD INFORMATION:
CARD TYPE:
VISA
MASTER CARD
CARD NUMBER
EXP. MONTH
YEAR
NAME - EXACTLY AS IT APPEARS ON YOUR CREDIT CARD
Part #
Description
Qty.
Price Each
$39.95
TOTAL
Remote Control
RC9900DVD
Shipping and Handling
Subtotal = ________ . ______
Subtotal + Tax
Up to $20.00
20.01 to 30.00
30.01 to 45.00
45.01 to 70.00
Over 70.01
Add
$5.00
5.95
6.50
6.95
7.95
California Residents Add Sales Tax = ________ . ______
Shipping and Handling (See Chart) = ________ . ______
TOTAL = ________ . ______
No C.O.D.’s
On regular orders please allow 4-5 weeks for delivery. Please give a shipping address where this order
may be delivered between the hours of 9 a.m. and 5 p.m. weekdays. If UPS is unable to deliver, your order will be
returned and additional shipping charges will be required.
31
Warranty
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within 1 year from the date of sale to you,
repair, replace or refund the retail sales price of said product or any part thereof, at the option
of the Magnadyne Corporation or its authorized agents, if said product or part is found defec-
tive in materials or workmanship, when properly connected and operating on the correct power
requirements designated for the specific product. This warranty and Magnadyne Corporation or
its authorized agents obligations hereunder do not apply where the product was; damaged
while in the possession of the consumer, subjected to unreasonable or unintended use, not rea-
sonably maintained, utilized in commercial or industrial operations, or serviced by anyone other
than Magnadyne Corporation or its authorized agents, or where the warning seal on the prod-
uct is broken or the power and/or plugs are detached from the unit. Magnadyne Corporation or
any of its authorized agents will not assume any labor costs for the removal and re-installation
of any product found to be defective, or the cost of transportation to Magnadyne Corporation
or its authorized agents. Such cost are the sole responsibility of the purchaser.
This warranty does not cover the cabinet appearance items or accessories used in connection
with this product, or any damage to recording or recording tape, or any damage to the prod-
ucts resulting from improper installation, alteration, accident, misuse, abuse or acts of nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO ANY-
ONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE ACCORD-
ED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT THOSE
SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND 1 YEAR FROM THE
DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not transferable.
Some states do not allow limitations on how long an implied warranty lasts and some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above lim-
itations or exclusion may not apply to you. This warranty gives you specific legal rights and you
may have other rights that vary from state to state.
Defective merchandise should be returned to the original point of purchase or secondly, to
Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220. Return Authorization
must be obtained before sending, or merchandise may be refused.
M9900DVDS-UM
Rev. C 4-26-06
© Copyright 2006
Magnadyne Corporation
|