Barco, Inc.
Toll Free: +1 (888) 414-7226
Fax: +1 (916) 859-2515
Technical Support: +1 (866) 374-7878
PDS Series
Quick Start Guide
Visibly yours
Menu Display
Adjust
SEL
Inputs Section
Button States
Use ADJUST knob,
plus SEL and ESC
buttons to navigate
menus.
• Counter-clockwise: scroll down
menu tree, or decrement values.
Press to enter a menu,
change or accept a
parameter, or answer
“Yes” to a query.
Sources 1-4: Analog
Sources 5-8*: DVI or Analog
Off: Input not selected
Blinking: Input “pending” for transition
Lit solid: Input on Program
• Clockwise: scroll up menu tree,
or increment values.
SDI: 3G/HD/SD-SDI
LOGO: Full screen capture
* (sources 7-8 not on PDS-701)
Inputs
PDS-902
PROGRAM:
NEXT:
RGB
1024x768@59.94
SDI
4
3
5
6
7
8
SEL
ESC
1
2
SDI
LOGO
TAKE
FRZ
BLACK
Adjust
NTSC (480i)
Effects
NOTE
ESC
FRZ
BLACK
TAKE
After each
TAKE, Program
and pending
Press to exit a menu
without making changes,
cancel an operation, or
answer “No” to a query.
Press to freeze or
un-freeze current
Program source.
Lit solid = frozen.
Press to pend or initiate a black transition.
Black Auto Take mode affects function
(User Preferences). Blinking = Pending.
Lit solid = Black on Program.
Press to mix the selected input
to Program, or to execute a pending
black transition. Use the Setup Menu
to adjust the transition time.
sources flip-flop.
Factory Reset – When using a PDS for the first
time, perform a factory reset. (Chapter 4,
“Factory Reset Menu”)
Repeat for Each Input — Repeat steps 10 and
11 for each input that you have connected to the
PDS.
5
12
13
14
15
16
Quick Setup and Operations
Launch GUI — (Optional) Connect your laptop to the
PDS, log onto the PDS using its IP address, and
launch the GUI. (Chapter 5, “GUI Operations”)
Adjust System Parameters — Adjust parameters
such as transition time, display brightness, user prefs.
(Chapter 4, “User Preference Menu,” “System Menu”)
6
7
The following list summarizes PDS setup and
operations. For error-free installation, always
refer to the listed section in the User’s Guide.
Set Output Format — Set the desired output
resolution and frame rate. (Chapter 4, “Output
Format”)
Save System Configuration — After completing all
system adjustments, save the system configuration.
(Chapter 4, “Save System State”)
Enable Test Pattern — Turn on a test pattern, verify
an image, and adjust as required. When complete,
turn off the pattern. (Chapter 4, “Test Pattern”)
Enable Remote Control — (Optional) Connect
Ethernet or Serial communications, and issue desired
commands. (Appendix B, “Remote Control”)
Connect Power — Ensure that power is properly
connected to the PDS. (Chapter 3, “Cable and
Adapter Information”)
8
1
2
3
4
Save Output Configuration — After completing all
output adjustments, save the output configuration.
(Chapter 4, “Save Config”)
Ready to Roll — With all output, input and system
configurations saved, press the desired input button,
and press TAKE.
Connect Inputs — Connect all analog, DVI, and
SDI input sources to the PDS. (Chapter 3, “Signal
Installation”)
9
Select and Adjust Input — Select an input, and
perform the necessary image adjustments. (Chapter
4, “Input Menu”)
Connect Outputs — Connect the output(s) of the
PDS to your projector(s) or other target devices.
(Chapter 3, “Signal Installation”)
10
11
Save Input Configuration — After completing all
adjustments for an input, save the input configuration.
(Chapter 4, “Save Config”)
Power On — Turn on power to the PDS, your
projector(s), and to all peripheral equipment.
(Chapter 4, “Power-Up Initialization”)
P/N 26-1204004-00 Rev 01
|
Actiontec electronic Network Card 802UI3 User Manual
Actiontec electronic Network Router UD800TP User Manual
ADT Security Services Home Security System 3000EN User Manual
AEG Microwave Oven MCC3880E M User Manual
American DJ DJ Equipment BU 200 User Manual
AO Smith Water Heater AOSRG45700 User Manual
Atlona TV Cables AT HD30SR User Manual
Audiovox Remote Starter 128 4246A User Manual
Axis Communications Security Camera P5414 E User Manual
Beko Flat Panel Television 40WLU530HID User Manual