OWNER’S
MANUAL
COLOR TV/VCR
SC313B (13 inch)
SC319B (19 inch)
This Owner’s Manual is made of
recycled paper.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an ENERGY STAR®
Partner, our company has
determined that this product meets
the ENERGY STAR® guidelines for
energy efficiency. ENERGY STAR® is
a U.S. registered mark.
If you need additional assistance for set-up or operating
after reading owner’s manual, please call
TOLL FREE : 1-800-242-7158.
Please read before using this equipment
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD I N
WI RE
GROUND
CL AMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRI C
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/VCR, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
19.Damage Requiring Service-Unplug this TV/VCR from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/VCR.
c. If the TV/VCR has been exposed to rain or water.
d. If the TV/VCR does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the TV/VCR to its normal operation.
14.Lightning-For added protection for this TV/VCR receiver
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the TV/VCR due to lightning and
power-line surges.
e. If the TV/VCR has been dropped or damaged in any way.
f. When the TV/VCR exhibits a distinct change in perfor-
mance-this indicates a need for service.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
21.Safety Check-Upon completion of any service or repairs to
this TV/VCR, ask the service technician to perform routine
safety checks to determine that the TV/VCR is in proper
operating condition.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/VCR through openings as they may touch dan-
gerous voltage points or short out parts that could result in
a fire or electric shock. Never spill liquid of any kind on
the TV/VCR.
22.Heat-This TV/VCR product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this TV/VCR yourself
as opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to quali-
fied service personnel.
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
- 3 -
EN
9I03
PRECAUTIONS
IMPORTANT COPYRIGHT INFORMATION
LOCATION
For safe operation and satisfactory performance of
your TV/VCR, keep the following in mind when
selecting a place for its installation:
Shield it from direct sunlight and keep it away
from sources of intense heat.
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
at the top and bottom of the unit. Do not place the
unit on a carpet because this will block the ventila-
tion holes.
Unauthorized recording or use of broadcast televi-
sion programming, video tape, film or other copy-
righted material may violate applicable copyright
laws. We assume no responsibility for the unautho-
rized duplication, use, or other acts which infringe
upon the rights of copyright owners.
•
•
•
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
Do not place the TV/VCR near strong magnetic fields.
Avoid moving TV/VCR to locations where temper-
•
•
•
•
ature differences are extreme.
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/VCR cassette holder.
Do not place anything directly on top of the unit.
•
•
•
•
•
WARNING
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. If a tape is played in a TV/VCR
which has moisture, it may damage the tape and
TV/VCR. Therefore when the condensation occurs
inside the unit, turn the POWER button on and allow
at least 2 hours for the unit to dry out.
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial
number as yours. You should record the number and other vital information here and retain this book as a per-
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
- 4 -
EN
9I03
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .17
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .18
PICTURE CONROLS . . . . . . . . . . . . . . . . . . .19
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
AVOID THE HAZARDS OF ELECTRICAL
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6
C OPERATING CONTROLS AND FUNCTIONS 7
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19
NORMAL RECORDING . . . . . . . . . . . . . . . . .20
SKIPPING UNWANTED SCENES DURING
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20
OTR (One Touch Recording) . . . . . . . . . . . . . .20
TIMER RECORDING . . . . . . . . . . . . . . . . . . .21
TIMER PROGRAM EXTENSION . . . . . . . . .22
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9
ANTENNA/CABLE CONNECTIONS . . . . . . .9
INSTALLING THE BATTERIES . . . . . . . . . . .10
EXTERNAL INPUT MODE . . . . . . . . . . . . . .10
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10
CHANNEL SET UP FOR THE FIRST TIME .10
CLOCK SET UP (AUTO / MANUAL) . . . . . .11
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .12
DELETING (OR ADDING) CHANNEL . . . . .12
SELECTING THE LANGUAGE . . . . . . . . . . .13
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24
C COPYING A VIDEO CASSETTE . . . . . . . . . .24
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25
REAL TIME TAPE COUNTER . . . . . . . . . . . .25
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14
WATCHING A TV PROGRAM . . . . . . . . . . . .14
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14
CLOSED CAPTION SYSTEM . . . . . . . . . . . .15
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25
C TROUBLESHOOTING GUIDE . . . . . . . . . . .26
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27
C CABLE CHANNEL DESIGNATIONS . . . . . .27
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover
TABLE OF CONTENTS
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-
tions concerning chemical wastes.
- 5 -
EN
9I03
FEATURES
Infrared remote control
Zero Return–The tape returns to counter of
•
•
•
•
0:00:00 by rewinding or fast forwarding.
Still–“Freeze” the picture at any time, for close
viewing of a particular scene. Only tapes recorded
in SLP mode will show a fairly clear picture.
Digital Auto Tracking (DTR)–Automatically
adjusts the tracking for each tape you play.
Rental play mode–Improves playback picture
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
Time search–Let you set the TV/VCR to advance
the tape by entering the desired playback time you
want to skip.
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible at the
push of the REC/OTR button.
1 Year, 8 events (including Daily and Weekly
Timer Recording)–The built-in timer allows you to
record up to 8 programs at different times on dif-
ferent channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broad-
casts, and the Weekly timer allows recording to be
made once a week up to the end of the tape.
Bilingual on screen menu display selectable in
English or Spanish
Real time counter–This shows the elapsed record-
ing or playback time in hours, minutes, and sec-
onds. The “–” indication will appear when the tape
is rewound further than the tape counter position
“0:00:00”.
181 channel capability PLL frequency synthesiz-
er tuner with direct station call–(A converter may
be necessary to view scrambled cable channels.)
Auto Clock Setting–Allows you to set the clock
function from a PBS broadcast station.
Closed caption system–You may view specially
labeled (cc) TV programs, movies, news, prere-
corded tapes, etc. with either a dialogue caption or
text display added to the program.
Game mode–Automatically sets external input
mode and allows TV/VCR display to be suitable
for use with TV games.
Auto power on and off system–Automatically
turns on the TV/VCR when you insert the cassette,
turns off after auto-rewind, and ejects when the
beginning of the tape is reached.
•
•
•
•
•
•
•
•
•
•
•
•
Auto rewind when the end of a tape is
reached–This function doesn’t occur when using
timer recording.
2 Step picture search operation–You can view a
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
Three different playback tape speeds : SP/LP/SLP
Two different recording tape speeds : SP/SLP
Auto Head Cleaner–Automatically cleans video
heads as you insert or remove a cassette.
Auto return–After timer recording is finished, the
TV/VCR can return to the beginning of the record-
ing.
Wake up/Sleep timer–Allows you to have the
TV/VCR automatically turn on or off at a desired
time.
Timer Program Extension–Allow you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
•
•
•
•
•
•
•
•
•
SUPPLIED ACCESSORIES
Remote Control Unit
2 AA Batteries
Rod Antenna (13” model only)
PART NO. (N0107UD?)
PART NO. (0EMN00673 or
0EMN01599)
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-
242-7158.
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators
(Splitter). Contact your local electronics store for these items.
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control. If you decide to use a universal remote control with this unit, please be aware
that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-
versal remote control.
•
•
•
- 6 -
EN
9I03
OPERATING CONTROLS AND FUNCTIONS
"
"
This manual covers 13 and 19 . The operation of the two models are exactly the same except the
"
appearance. 19 model is illustrated in this manual.
NOTE:
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
•
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
- TV/VCR FRONT PANEL - [Fig.1]
POWER
AUDIO
VIDEO
STOP/EJECT
REW
PLAY
F.FWD
CHANNEL
VOLUME
REC/OTR
EARPHONE
1
2 3 4 5 6 7 891011 12 13 14
1 EARPHONE jack– Connects to earphones (not sup-
plied) for personal listening. The size of jack is
1/8” monaural (3.5mm).
- REMOTE CONTROL - [Fig.2]
2 AUDIO input jack– Connect to the audio output
jack of your audio equipment, video camera or
another VCR.
3 VIDEO input jack– Connect to the video output
jack of your video camera or another VCR.
4 STOP button– Press to stop the tape motion.
EJECT button– Press in the Stop mode to remove
tape from TV/VCR.
25
4
WAKE-UP
POWER
/SLEEP
EJECT
13
15
CHANNEL
RETURN
1
4
7
2
5
8
3
6
9
24
CHANNEL
VOLUME
11
12
L button–
Press to select setting modes from the on screen
menu.
0
+100
•
MENU
DISPLAY
MUTE
16
17
5
Press to enter digits when setting program.
•
23
6
(for example: setting clock or timer program)
5 REW button– Press to rew¨ind the tape, or to view
the picture rapidly in reverse during playback
mode. (Rewind Search)
PLAY
7
REW
F.FWD
STOP
4
SPEED PAUSE/STILL
RECORD
s button–
22
21
8
18
T-PROG.
CLEAR
GAME
Press to select a mode from a particular menu.
TIME SEARCH
•
(for example: LANGUAGE or USER’S SET UP)
6 PLAY button– Press to begin playback.
K button–
Press to select setting modes from the on screen
menu.
COUNTER
RESET
19
20
•
Press to enter digits when setting program.
(for example: setting clock or timer program)
•
- 7 -
EN
9I03
- REAR VIEW - [Fig.3]
ANT.
26
27
+100 button– When selecting cable channels
which are higher than 99, press this button first,
then press the last two digits. (To select channel
125, first press the “+100” button then press “2”
and “5”).
7 F.FWD button– Press to rapidly advance the tape,
or to view the picture rapidly in forward during
playback mode. (Forward Search)
B button–
When setting program (for example: setting clock
•
16 MENU button– Press to display the main menu on
the TV screen.
17 DISPLAY button– Display the counter or the cur-
rent channel number and current time on the TV
screen. (See page 25.)
or timer program), press to determine your selec-
tion and proceed to the next step you want to
input.
Press to determine setting modes from on screen
menu.
•
18 SPEED button– Press to choose the desired
recording speed:SP/SLP.
19 T-PROG. CLEAR button– Press to cancel a setting
of timer program. (See page 23.)
COUNTER RESET button– Press to reset counter
to 0:00:00.
20 GAME button– Sets the game mode and external
input mode at the same time. (See page 14.)
21 TIME SEARCH button– Press to activate Time
Search mode.
Press to select a mode from a particular menu.
•
(for example: LANGUAGE or USER’S SET UP)
8 REC button– Press for manual recording.
OTR button– Activates One Touch Recording.
(only on the TV/VCR)
9 RECORD indicator– Flashes during recording.
Lights up in the Stand-by mode for Timer
Recording.
10 Remote Sensor Window– Receives the infrared
signals from the remote control.
22 PAUSE/STILL button– Press to temporarily stop
the tape during the recording or to view a still pic-
ture during playback.
23 MUTE button– Mutes the sound. Press it again to
resume sound.
11 CHANNEL K / L buttons– Press to select the
desired channels for viewing or recording.
You may display the main menu on the TV screen
by pressing repeatedly this button on the
TV/VCR.
24 CHANNEL RETURN button– Press to go back to
the previously viewed channel. For example,
pressing this button once will change channel dis-
play from 3 (present channel) to 10 (previously
viewed channel), and pressing it a second time
will return from 10 to 3.
25 WAKE UP/SLEEP button– Sets the Wake up or
Sleep Timer. (See page 23.)
26 Power cord– Connect to a standard AC outlet
(120V/60Hz).
TRACKING function– Press to minimize video
‘noise’ (lines or dots on screen) during playback
mode. (See page 19.)
12 VOLUME X / Y buttons– Adjust the volume
level.
13 POWER button– Press to turn TV/VCR on and
off. Press to activate timer recording.
14 Cassette compartment
15 Number buttons– Press to select desired channels
for viewing or recording. To select channels from
1 to 9, first press the 0 button and then 1 to 9.
27 ANT. terminal– Connect to an antenna or cable
system.
- 8 -
EN
9I03
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
From Cable System or
Satellite Dish
VHF/UHF Antenna
(Not supplied)
Satellite Box or
Cable Box
Rod Antenna
(Supplied with 13” model only)
OUT
IN
(Not supplied)
VHF Antenna
(Not supplied)
UHF Antenna
(Not supplied)
From
Cable System
or
ANT.
VHF/UHF
Combiner
(Not supplied)
or
ANT.
or
75-ohm Coaxial
Cable (Not supplied)
Flat twin-lead cable
or
VHF/UHF COMBINED ANTENNA
VHF/UHF SEPARATE ANTENNAS
The VHF/UHF Rod Antenna (supplied wuth 13”
model only) is detachable. Insert the stem of the
antenna into the hole on the upper-back portion of
the TV/VCR.Connect the VHF/UHF Rod Antenna or
VHF/UHF Combination Antenna to the ANT. termi-
nal of the TV/VCR as shown in the diagram
below.For the best reception, fully extend the
VHF/UHF Rod Antenna and make the necessary
adjustments. (Avoid touching the top section when
adjusting.)
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to your TV/VCR without a converter box.
By using this connection you can:
1) Use the TV/VCR remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE:
Before plugging the Rod antenna into antenna termi-
nal, check that the pin is not bent. If it is bent,
straighten the pin as illustrated, then plug the pin into
antenna terminal.
NOTE: This unit will ONLY record and view the
same channel.
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
Bent pin
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown here.
By using this connection you can also record scram-
bled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/VCR Remote Control. Unattended timer record-
ing is limited to one channel at a time.
Cable Plug
(Straight pin)
(Needs to be straightened)
NOTE:
The connection of an indoor antenna may not always
give acceptable TV reception.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-
ed to the grounding system of the building as close to the point of cable entry as practical.
- 9 -
EN
9I03
TO RECORD A SCRAMBLED/UNSCRAMBLED
CHANNEL
INSTALLING THE BATTERIES
1. Set the TV/VCR channel selector to the output
channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
EXTERNAL INPUT MODE
When using an external input signal (another VCR or
video camera), connect the player’s audio/video out-
put cables to the AUDIO IN/ VIDEO IN jacks of
your TV/VCR. Then press the CHANNEL K or
L
button until “AUX” appears on the screen.
AUX
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then
select the channel to be viewed on the Cable Box or Satellite Box.
The tuner scans and memorizes all active channels in
your area.
NOTES:
CHANNEL SET UP FOR THE
FIRST TIME
The TV/VCR distinguishes between standard TV
channels and cable channels.
If you want to play or record a video tape
BEFORE presetting the tuner, you must press the
MENU button on the remote control. To preset the
tuner again, see “CHANNEL SET UP AGAIN” on
page 12.
The TV/VCR may recognize TV channels to be
CATV channels by the receiving conditions. In this
case, try auto preset again in the fine receiving
conditions.
•
1 Plug in the TV/VCR power cord
Plug the TV/VCR power cord into a
•
standard AC outlet.
NOTE:
If some digits appear in the corner of
the screen, press the POWER button
without unplugging the power cord.
•
•
2 Turn on the TV/VCR
Press the POWER button to turn on the TV/VCR
5 After scanning
3 Select “ENGLISH” or “ESPAÑOL”
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can
select the desired channel directly with the remote
control number buttons or CHANNEL K or L.
– SET UP –
Select “ENGLISH” or
“ESPAÑOL”=Spanish using the
F.FWD/B or REW/s button. “[ ]”
indicate the selected language.
B
LANGUAGE
[ENGLISH] ESPAÑOL
AUTO PRESET
4 Begin auto preset
– SET UP –
Press the PLAY/K or STOP/L but-
ton to point to “AUTO PRESET”.
Then press the F.FWD/B button.
LANGUAGE
[ENGLISH] ESPAÑOL
B
AUTO PRESET
- 10 -
EN
9I03
1 Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “SETTING
CLOCK”.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TO SELECT ADESIRED CHANNEL
B
You can select the desires channel by using the
CHANNEL K or L button on or directly pressing
the number buttons on the remote control.
Note for using the number buttons:
ZERO RETURN
TIME SEARCH
Then, press the F.FWD/B button.
When selecting cable channels which are higher
•
than 99, press the +100 button first, then, press the
last tw odigts. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
– SETTING CLOCK –
2 Set “AUTO CLOCK” to [ON]
Press the F.FWD/B or REW/s
button repeatedly until [ON]
appears.
B
AUTO CLOCK
[ON]
AUTO CLOCK CH
[AUTO]
[OFF]
You must procede single-digit channel numbers
with a zero (Example: 02 ... 09).
•
MANUAL CLOCK SET
D.S.T.
CLOCK SET UP
(AUTO / MANUAL)
3 Enter the channel number for the PBS station
Press the PLAY/K or STOP/L button to point to
“AUTO CLOCK CH”.
Then press the F.FWD/B or
REW/s button until the channel
number for your local PBS station
appears.
– SETTING CLOCK –
Set the clock accurately for proper automatic timer
recording. If the Public Broadcasting Station (PBS)
is available in your area, follow “AUTO CLOCK
SETTING”. If it is not, follow “MANUAL CLOCK
SETTING”.
AUTO CLOCK
[ON]
B
AUTO CLOCK CH
[AUTO]
MANUAL CLOCK SET
D.S.T.
[OFF]
If you do not know the PBS channel
number, leave it set to [AUTO] which is located
AUTO CLOCK SETTING
before [2]. The TV/VCR will search automatically all
available channels for the local PBS station, and will
select that channel.
You can have the TV/VCR set the clock automatical-
ly by using the Public Broadcasting Station (PBS)
channel in your area. Once you have set the clock by
using the following procedure, the TV/VCR will
automatically monitor the correct time and date
being broadcast by the PBS station in your area,
using a new service called Extended Data Service
(XDS).
4 Exit the Auto Clock Setting
Press the MENU button on the remote control to
return to TV mode.
5 Turn off the TV/VCR
Turn the TV/VCR off. Because the Auto Clock func-
tions automatically while the TV/VCR is off.
Make sure ...
TV/VCR power must be turned on.
Confirm that the antenna connections are correct.
The cable converter box must be turned on if your
TV/VCR is connected directly to it. (See NOTES:)
•
•
•
If you choose [AUTO],
The channel is properly set in advance.
•
The TV/VCR must search until the PBS channel is
•
found. It must scan each channel for a couple of
seconds to determine if that channel is transmitting
the XDS signal.
NOTES:
Auto clock setting only needs to be set once. But it
can be done again if the clock’s time has become
incorrect for some reason.
•
If the time, that is automatically set by this select-
•
ed PBS station is incorrect, it may not be your
local PBS station, but one from a different time
zone. Or there is a case that no channel is broad-
casting the XDS signal in your area, as shown by
no time. In these cases, you must manually enter
the correct local PBS station, or set the clock man-
ually and turn off the Auto Clock Setting feature.
If the TV/VCR is connected directly to a cable
•
converter box or satellite box, the local PBS station
must be selected on the cable box itself, and the
TV/VCR must be set to the output channel of the
cable converter box or satellite box (usually chan-
nel 3 or 4), to be able to set up or correct the clock
automatically.
If you do not know what your local PBS station is,
then follow “Manual Clock Settings”.
The TV/VCR cannot control the channels of the
cable converter box or satellite box.
MANUAL CLOCK SETTING
Make sure ...
TV/VCR power must be turned on.
In the example below, the clock is to be set to:
•
DATE
May 1st, 2001
SETTING TIME 5:40PM
- 11 -
EN
9I03
NOTE:
When unplugging the AC cord or if there is a power
failure for more than 30 seconds, you may have to
reset the clock.
1 Select “SETTING CLOCK”
Press the MENU button on the remote control.
– M E N U –
Press the PLAY/K or STOP/L but-
TIMER PROGRAMMING
ton to point to “SETTING
CLOCK”.
Then, press the F.FWD/B button.
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps [1] and [2].
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
2)Select where you want to change using the
F.FWD/B or REW/s button.
3)Enter correct numbers using the PLAY/K or
STOP/L button.
4)Press the MENU button on the remote control to
start the clock.
2 Select “MANUAL CLOCK SET”
Press the PLAY/K or STOP/L button to point to
“MANUAL CLOCK SET”.
Then, press the F.FWD/B button.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH
[AUTO]
[OFF]
B
MANUAL CLOCK SET
D.S.T.
3 Select the month
PLEASE NOTE:
Press the PLAY/K or STOP/L but-
ton until your desired month
appears. (Example: May → 05)
Then, press the F.FWD/B button.
– MANUAL CLOCK SET –
MONTH DAY YEAR
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and press
the F.FWD/B or REW/s button to turn [OFF] this
function. Then you can manually adjust the clock.
0 5
/
– – – – – – – – –
HOUR
MINUTE
– –
:
– – – –
– MANUAL CLOCK SET –
MONTH DAY YEAR
4 Select the day
CHANNEL SET UP AGAIN
Make sure ...
Press the PLAY/K or STOP/L but-
ton until your desired day appears.
(Example: 1st → 01)
0 5
/
0 1 – – – – – – –
HOUR
MINUTE
Press the POWER button to turn on the TV/VCR.
•
– –
:
– – – –
Then, press the F.FWD/B button.
1 Select “CHANNEL SET UP”
– M E N U –
Press the MENU button on the
TIMER PROGRAMMING
– MANUAL CLOCK SET –
MONTH DAY YEAR
5 Select the year
Press the PLAY/K or STOP/L but-
ton until your desired year appears.
(Example: 2001)
PICTURE CONTROL
remote control.
SETTING CLOCK
B
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
0 5
/
0 1 THU 2 0 0 1
Press the PLAY/K or STOP/L but-
ton to point to “CHANNEL SET
UP”.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
HOUR
MINUTE
TIME SEARCH
– –
:
– – – –
Then, press the F.FWD/B button.
Then, press the F.FWD/B button.
– MANUAL CLOCK SET –
MONTH DAY YEAR
6 Select the hour
Press the PLAY/K or STOP/L but-
ton until your desired hour appears.
(Example: 5, PM)
2 Begin auto preset
– CHANNEL SET UP –
0 5
/
0 1 TUE 2 0 0 1
ADD / DELETE CH (TV)
AUTO PRESET
Press the PLAY/K or STOP/L but-
ton to point to “AUTO PRESET”.
Then, press the F.FWD/B button.
The tuner scans and memorizes all
the active channels in your area.
B
HOUR
0 5
MINUTE
:
– – PM
Then, press the F.FWD/B button.
– MANUAL CLOCK SET –
MONTH DAY YEAR
7 Select the minute
Press the PLAY/K or STOP/L but-
ton until the desired minute
appears. (Example: 40)
0 5
/
0 1 TUE 2 0 0 1
3 After scanning
HOUR
0 5
MINUTE
4 0 PM
The tuner stops on the lowest memorized channel.
:
DELETING (OR ADDING)
CHANNEL
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
8 Start the clock
Press the MENU button on the
remote control.
Although seconds are not displayed,
they begin counting from 00 when
you press the MENU button on the
5:40 PM
remote control. Use this feature to synchronize the
clock with the correct time.
- 12 -
EN
9I03
1 Select “CHANNEL SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “CHANNEL SET
UP”.
2 Select “ENGLISH” or “ESPAÑOL”
Select “ENGLISH” or “ESPAÑOL”= Spanish using
the F.FWD/B or REW/s button.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B
3 Exit the Language mode
Press the MENU button on the remote control to
return to TV mode.
ZERO RETURN
TIME SEARCH
Then, press the F.FWD/B button.
NOTE: If for some reason the menu is in Spanish,
press the MENU button on the remote control, press
the PLAY/K button to point to “IDIOMA
[ESPAÑOL]”, then press the F.FWD/B button, then
press the MENU button on the remote control.
– CHANNEL SET UP –
2 Select “ADD/DELETE CH”
Press the PLAY/K or STOP/L but-
ton to point to “ADD/DELETE
CH”.
B
ADD / DELETE CH (TV)
AUTO PRESET
Press the F.FWD/B button.
DAYLIGHT-SAVING TIME
3 Enter the desired channel number
Press the PLAY/K or STOP/L but-
ton until your desired channel num-
ber appears. (You can also use the
number buttons or the CHANNEL
K/L button to enter it) (Example:
CH8)
Select this feature and the TV/VCR’s clock automati-
cally will advance one hour in April, then reverse one
hour in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
08
ADD / DELETE
First Sunday of April : At 2 AM the clock imme-
•
diately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
4 Delete (or add) it from (into) memory
Press the F.FWD/B or REW/s button. The channel
number changes to light red. The channel is deleted
from memory.
Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
Press the POWER button to turn on the TV/VCR.
•
To delete another channel, repeat steps [3] and [4].
If you press the F.FWD/B or REW/s button
•
•
•
again, the channel is memorized again.
1 Select “SETTING CLOCK”
Press the MENU button on the
– M E N U –
remote control.
Added channel: Light blue.
Deleted channel: Light red.
TIMER PROGRAMMING
PICTURE CONTROL
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the PLAY/K or STOP/L but-
ton to point to “SETTING
CLOCK”.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
5 Exit the channel setup mode
Press the MENU button on the remote control to
returns to TV mode.
TIME SEARCH
Then, press the F.FWD/B button.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL K or L button.
2 Set “D.S.T.” (Daylight-Saving Time) to [ON]
– SETTING CLOCK –
Press the PLAY/K or STOP/L but-
AUTO CLOCK
[ON]
ton to point to “D.S.T.”.
AUTO CLOCK CH
[AUTO]
[ON]
Then, press the F.FWD/B or
REW/s button until [ON] appears.
MANUAL CLOCK SET
D.S.T.
SELECTING THE LANGUAGE
B
Make sure ...
Press the POWER button to turn on the TV/VCR.
NOTE: This function effects only the language on
•
3 Exit the Daylight-Saving Time mode
Press the MENU button on the remote control to
return to TV mode.
the screen menu and not the audio source.
1 Select “LANGUAGE”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “LANGUAGE”.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the
B
ZERO RETURN
TIME SEARCH
F.FWD/B or REW/s button.
- 13 -
EN
9I03
TV OPERATION
WATCHING A TV PROGRAM
PICTURE CONTROL
The TV/VCR’s picture controls – BRIGHT, CON-
TRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a natural looking image.
NOTES:
1 Turn on the TV/VCR
Press the POWER button to turn on the TV/VCR.
2 Select the channel number
Press the CHANNEL K or L button to select your
desired channel number or press the number buttons
on the remote control.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be viewed must be selected
on the cable box or satellite box.
Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
When setting the Picture Control, the Game mode
will be cancelled.
•
•
Make sure ...
TV/VCR power must be turned on.
•
1 Select “PICTURE CONTROL”
3 Adjust sound
Press the VOLUME or button
to adjust the volume.
Press the MENU button on the
X
Y
– M E N U –
remote control.
TIMER PROGRAMMING
B
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the PLAY/K or STOP/L but-
ton to point to ”PICTURE CON-
TROL”.
VOLUME 20
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
C
C
C
C
C
C
C
C
C
C
C
C
TIME SEARCH
Then, press the F.FWD/B button.
GAME MODE
2 Select item you want to adjust
Press the PLAY/K or STOP/L button until desired
This function enables you to decrease the TV screen
contrast and making it suitable for use with a TV
GAME.
control is displayed.
BRIGHT
CONTRAST
NOTE: This function can not be set during recording.
BRIGHT
COLOR
–
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +
TINT
Press the GAME button on the
GAME
remote control. “GAME” appears
on the screen.
SHARPNESS
3 Adjust the picture control
When you press the GAME button;
Press the F.FWD/B or REW/s button to adjust to
The TV/VCR comes on automatically if it is off.
The TV/VCR will be in external input mode auto-
•
•
your desired level.
matically.
TO CANCEL THE GAME MODE
Press the GAME button or CHANNEL K or L but-
ton on the remote control.
REW/s
to decrease
brightness
to decrease
contrast
F.FWD/B
to increase
brightness
to increase
contrast
BRIGHT
CONTRAST
DEGAUSSING
Magnetism from nearby appliances might affect the
color of the TV picture.
If this happens, move this unit away from the appli-
ance. If the color is still not correct, disconnect
power cord from AC outlet then reconnect it after 30
minutes.
COLOR
TINT
to pale
to brilliant
to purple
SHARPNESS to soft
to green
to clear
If there is a power failure of any kind, the unit will
retain its memory for this feature.
•
- 14 -
EN
9I03
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button. Press the MENU but-
ton on the remote control to return to TV mode.
CLOSED CAPTION SYSTEM
You can view specially labeled (cc) TV programs,
movies, news, pre-recorded tapes with either a dia-
logue caption or text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used,
usually for a second language if available.
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 sec-
onds.
This is also true when the MUTE button is pressed,
and when the PAUSE/STILL button is pressed
while recording.
•
If there is a power failure of any kind, the unit will
retain its memory for this feature.
NOTE:
•
Not all programs are broadcast with closed captions.
Your television is designed to provide error free
closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are
likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions
errors are listed below:
V-CHIP SET UP
V-CHIP enables parents to prevent their children
from watching inappropriate material on TV.
V-CHIP reads the ratings for programming (except
for news and sports programs, unedited movies on
premium cable channels, and Emergency Broadcast
System signals), then denies access to programming
if the program’s rating meets the limitations you
select. In this case, “PROTECTED PROGRAM by
...” message appears on the TV screen.
To block ratings, follow the steps below.
Programming may be rated by the Motion Picture
Association of America (MPAA) or according to
the Television Parental Guidelines. In order to
block any inappropriate programming, set your
limits in both places (MPAA RATING and TV
RATING).
Automobile ignition noise
Electric motor brush noise
Weak snowy reception on TV screen
Multiplex signal reception displaying picture
•
•
•
•
ghosts or airplane flutter.
Playback of poorly recorded or worn VCR tapes.
NOTE:
•
If the TV/VCR displays a black box on the TV
screen, this means that the TV/VCR
is set to the TEXT mode. To clear
screen, select [CAPTION1], [CAP-
TION2] or [OFF].
•
Make sure ...
TV/VCR power must be turned on.
•
TV RATING SET UP
– M E N U –
1 Select “CAPTION”
Make sure ...
TIMER PROGRAMMING
PICTURE CONTROL
Press the MENU button on the
SETTING CLOCK
TV/VCR power must be turned on.
CHANNEL SET UP
•
USER’S SET UP
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “CAPTION”.
V-CHIP SET UP
LANGUAGE [ENGLISH]
B
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
1 Select “V-CHIP SET UP”
– M E N U –
TIMER PROGRAMMING
Press the MENU button on the
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
remote control.
USER’S SET UP
2 Select your desired caption menu
Press the F.FWD/B or REW/s
button until your desired caption
menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Press the PLAY/K or STOP/L but-
ton to point to “V-CHIP SET UP”.
Then, press the F.FWD/B button.
– M E N U –
TIME SEARCH
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION1]
ZERO RETURN
B
TIME SEARCH
2 Select “TV RATING”
– V-CHIP SET UP –
B
TV RATING
MPAA RATING
Press the PLAY/K or STOP/L but-
ton to point to “TV RATING”.
Then, press the F.FWD/B button.
3 Exit the caption setting mode
Press the MENU button on the remote control to
return to TV mode.
- 15 -
EN
9I03
3 Select your desired item
Press the PLAY/K or STOP/L button to point to
your desired item.
4 Exit the V-Chip setting mode
Press the MENU button on the remote control to
return to original mode.
Then, press the F.FWD/B button to
select [BLOCK] or [VIEW].
B
TV–Y
TV–Y7
TV–G
TV–PG (
TV–14
TV–MA(
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
MPAA RATING SET UP
(
)
)
)
)
(
Make sure ...
When you select the rating cate-
gory and turn it [BLOCK], the
higher rating will turn [BLOCK]
•
TV/VCR power must be turned on.
•
automatically. Also, the lower rating will turn
[VIEW] automatically.
When you turn “TV-Y” to [VIEW], the all ratings
will turn to [VIEW] automatically.
1 Select “V-CHIP SET UP”
– M E N U –
Press the MENU button on the
TIMER PROGRAMMING
•
PICTURE CONTROL
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “V-CHIP SET UP”.
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
When you select TV-Y7, TV-PG, TV-14, or TV-MA
TIME SEARCH
Selection
TV-Y
Rating Category Explanations
Appropriate for all children
Then, press the F.FWD/B button.
TV-Y7
TV-G
TV-PG
TV-14
Appropriate for children seven and older
General Audience
Parental Guidance suggested.
Unsuitable for children under 14
2 Select “MPAA RATING”
– V-CHIP SET UP –
Press the PLAY/K or STOP/L but-
ton to point to “MPAA RATING”.
Then, press the F.FWD/B button.
TV RATING
MPAA RATING
B
TV-MA Mature audience only
and you press the F.FWD/B button, the sub-ratings
will appear on the TV screen.
If you select the rating category (example: TV-PG)
and turn it [BLOCK] or [VIEW], the sub-ratings
(example: V for Violence) will turn [BLOCK] or
[VIEW] automatically.
You can set the sub-ratings to [BLOCK] or [VIEW]
individually when the rating category is set to
[BLOCK].
3 Select your desired item
Press the PLAY/K or STOP/L but-
ton to point to your desired item.
Then, press the F.FWD/B button to
select [BLOCK] or [VIEW].
G
[VIEW]
PG
[VIEW]
PG–13
R
NC–17
X
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
When you select the rating cate-
•
Selection
G
Rating Category Explanations
General Audience
PG
PG-13
R
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompa-
nying parent or adult guardian
No one under 17 admitted
To set the sub-ratings individually, follow the steps
below.
When you select [TV-Y7]:
•
TV–Y7
[BLOCK]
[BLOCK]
Press the STOP/L or PLAY/K
button to select “FV” (Fantasy
Violence).
B
FV
NC-17
X
Mature audience only
Then, press the F.FWD/B button
to select [BLOCK] or [VIEW].
gory and turn it [BLOCK], the higher rating will
turn [BLOCK] automatically. Also, the lower rat-
ing will turn [VIEW] automatically.
When you turn “G” to [VIEW], the all ratings will
turn to [VIEW] automatically.
When you select [TV-PG], [TV-14] or [TV-MA]:
Press the STOP/L or PLAY/K
•
•
•
button to select “D”(Suggestive
TV–PG
[BLOCK]
B
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Dialog), “L”(Coarse Language),
“S”(Sexual Situation), or
“V”(Violence). Then, press the
F.FWD/B button to select
[BLOCK] or [VIEW].
4 Exit the V-Chip setting mode
Press the MENU button on the remote control to
return to original mode.
Note: When you select [TV-MA], “D” does not
appear on the TV screen.
The sub-ratings which set to
B
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
(
)
[VIEW]
[VIEW]
[BLOCK] appears next to the rat-
ing category in the TV RATING
menu.
[BLOCK]
[BLOCK]
[BLOCK]
- 16 -
EN
9I03
PLAYBACK
This TV/VCR will operate with any cassette that has the
mark. For best results, we
recommend the use of high-quality tapes. Do not us poor quality or damaged tapes.
INSERTING A CASSETTE
AUTO REPEAT PLAYBACK
Insert the cassette in the direction as shown. Push in
The TV/VCR has the auto repeat function that allows
gently, but continuously, on the center-back of the
you to repeat a tape indefinitely without touching the
cassette until it is drawn into the TV/VCR. The
PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
TV/VCR will automatically turn on.
BLANK REPEAT: Repeat playback from the begin-
Window
ning to a blank part, which is blank for more than
10 seconds.
WRONG
CORRECT
1 Select “USER’S SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
NORMAL PLAYBACK
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Make sure ...
TV/VCR power must be turned on.
•
2 Select “ALL” or “BLANK”
1 Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/VCR will start playback automatically.
Press the PLAY/K or STOP/L button to point to
USER’S SET UP
–
–
“REPEAT PLAY”.
Press the F.FWD/B or REW/s
button repeatedly until your desired
selection [ALL] or [BLANK]
appears.
RENTAL
[OFF]
[ALL]
[OFF]
B
REPEAT PLAY
AUTO RETURN
2 To begin playback
Press the PLAY button.
Note:
If any menu is activated on the screen, the PLAY but-
ton does not function. Press the MENU button to
clear the menu. then, press the PLAY button.
If a tape is already on the TV/VCR with power off
2A) Press the PLAY button on the TV/VCR. Power
will automatically turn on and playback will start.
(Direct button operation)
3 Exit the Repeat Play setting
Press the MENU button on the remote control to
return to the TV mode.
4 Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY B” appears.
Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/VCR.
If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
2B) Use the remote control;
•
Press the PPOWER button to turn the TV/VCR on,
and then press the PLAY button on the remote con-
trol.
•
3 To stop playback
Press the STOP button when playback is completed.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button on the remote control.
Press the MENU button on the remote control to
return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
- 17 -
EN
9I03
NOTES:
SEARCH
Time Search can be set up to a maximum of 9
•
hours 50 minutes (9:50) by 10 minutes at a time.
PICTURE SEARCH
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
This function will not operate in recording mode.
•
In the example below: To watch a program after 2
hour 50 minutes from the present position, in either
direction.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD or REW button. (in the SP / LP / SLP
modes)
2)Press it again and the TV/VCR will now search in
super high speed. (in the LP / SLP modes only)
NOTE: Tapes recorded in the SP or LP mode will
display a noise bar on the TV screen and the pic-
ture may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
1 Insert a tape.
2 Select “TIME SEARCH” mode
Press the TIME SEARCH button (with each push it
will increase by 10 minute).
3 Enter your desired time
Press the PLAY/K or STOP/L but-
TIME SEARCH
2 : 50
ton until your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
If you wish to cancel the Time Search at this point,
press the MENU button on the remote control.
ZERO RETURN
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
4 Begin Time Search
By pressing the REW/s or F.FWD/B button, the
TV/VCR will rewind or fast forward to the specified
point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
1 Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
2 Reset the counter to 0:00:00
Press the COUNTER RESET button repeatedly.
TO CANCEL THE TIME SEARCH at this
point
Press the STOP/EJECT button on the TV/VCR or the
remote control. This will delete the selected time.
3 Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is
completed.
STILL PICTURE
You can view a still picture on the TV screen during
playback (the Still mode). Press the PAUSE/STILL
button during playback. Only tapes recorded in the
SLP mode will show the least amount of lines.Press
the PLAY button to return to playback.
NOTES:
4 To activate “ZERO RETURN” mode
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L button to point to
“ZERO RETURN”.
– M E N U –
TIMER PROGRAMMING
Then, press the F.FWD/B button.
PICTURE CONTROL
Usually there will be video “noise” lines (black
and white streaks or dots) on the screen. This is
normal.
SETTING CLOCK
•
CHANNEL SET UP
The counter will appear on the TV
USER’S SET UP
V-CHIP SET UP
screen.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B
The tape will automatically stop
when the counter returns to 0:00:00.
TIME SEARCH
If the tape was originally recorded in SP or LP
mode, the still picture will be black and white in
addition to the “noise” lines.
This is not a fault of the machine, but is a by-
product of the technology involved in producing
a TV/VCR with 2 video heads.
TIME SERACH
The Time Search function makes it possible to
quickly advance the tape to your desired position
simply by entering the exact amount of playback
time you want to skip.
If it is left in the Pause mode for more than five
minutes, the TV/VCR will automatically switch to
the Stop mode.
•
- 18 -
EN
9I03
NOISE CANCEL (in the Still mode)
RENTAL PLAYBACK
This feature allows you to reposition or reduce the
noise lines of a still picture.Press the PAUSE/STILL
button so that the noise lines change position on the
screen so you can see the picture in its entirety with-
out distracting noise lines.
NOTE: This feature can be activated ONLY when
viewing a tape recorded in the SLP mode. If the tape
was originally recorded in the SP or LP mode, the
still picture may revert to black and white in addition
to the “noise bars”. This is normal.
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1 Select “USER’S SET UP”
– M E N U –
TIMER PROGRAMMING
Press the MENU button on the
PICTURE CONTROL
SETTING CLOCK
remote control.
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press the PLAY/K or STOP/L but-
ton to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
VERTICAL HOLD CONTROL
In the Pause/Still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
the CHANNEL K or L button.
2 Set “RENTAL” to [ON]
Press the PLAY/K or STOP/L but-
ton to point to “RENTAL”.
Press the F.FWD/B or REW/s
button until [ON] appears.
USER’S SET UP
–
–
B
RENTAL
REPEAT PLAY
AUTO RETURN
[ON]
[OFF]
[OFF]
NOTE:
If there are video noise lines on the screen, reposition
or reduce them. Refer to “NOISE CANCEL”.
3 Exit the Rental setting
Press the MENU button on the remote control to
return to the TV mode.
PICTURE CONTROLS
TRACKING ADJUSTMENT
4 Start playback
Tracking adjustment will be set automatically
(Digital Tracking function) when you start play-
back.
•
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
Once you select the Rental mode, it stays in effect
even after you turn off the TV/VCR.
•
However when playing pre-recorded tapes or tapes
•
recorded on units other than your own, noise lines
(black and white streaks) may appear on the play-
back picture. If this occurs, you can adjust the
tracking control manually by pressing the CHAN-
NEL K or L button until the streaks disappear. To
return to the DTR function, stop the tape once and
start playback again.
TO CANCEL THE RENTAL MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button on the remote control.
Press the MENU button on the remote control to
return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
RECORDING
TWO DIFFERENT TAPE SPEEDS
ERASE PREVENTION
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/play-
back time using T60, T120 or T160 tapes in each
mode.
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tab
Tape Speed
Type of tape
SP mode
Recording/Playback Time
If you decide to record on
the tape again, cover the
hole with plastic tape.
T60
1 hour
3 hours
T120
T160
2 hours 2-2/3 hours
6 hours 8 hours
SLP mode
Note: You can play back a tape recorded in LP mode
(Long Play).
Transparent Tape
- 19 -
EN
9I03
Make sure ...
TV/VCR power must be turned on.
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
•
•
NOTE: This unit will ONLY record and view the same channel.
NORMAL RECORDING
OTR (One Touch Recording)
You can ONLY watch the same TV program that is
being recorded.
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/VCR.
Make sure ...
1 Select the channel to be recorded
TV/VCR power must be turned on.
Insert a cassette tape with its erase prevention tab
Press the number buttons on the
•
•
CH 10
remote control or the CHANNEL
K or L button.
in place. (If necessary, rewind or fast forward the
Remember: If the TV/VCR is con-
nected to a cable box or satellite
box, the TV/VCR must be on CH3
or CH4, then the channel to be recorded must be
selected on the cable box or satellite box.
tape to the point at which you want to begin
recording.)
NOTES:
This function CANNOT be done from the remote
control.
•
Recording starts immediately when the REC/OTR
button is pressed.
•
2 Select the tape speed
Press the SPEED button to select
the desired tape speed (SP/ SLP).
When the REC/OTR button is pressed 18 times, the
TV/VCR returns to the Normal Recording mode.
•
To stop the OTR operation, press the STOP button
on the TV/VCR or on the remote control.
•
SP
To show the remaining time, press the DISPLAY
•
button on the remote control so that “OTR”
appears on the TV screen. (It will show up momen-
tarily then disappear.)
REC
3 Begin recording
Press the RECORD button.
Recording stops when 0:00 is reached.
Please note that in the SLP mode maximum record-
ing time, assuming the tape is started at the begin-
ning, is 8 hours using T-160 (or 6 hours using T-120).
•
•
SP
4 Stop recording
Press the STOP button when recording is completed.
If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediate-
ly, ejects the tape and turns itself off.
•
SKIPPING UNWANTED
1 Select the channel to be recorded
Press the number buttons on the remote control or the
CHANNEL K or L button.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be recorded is selected on
the cable box or satellite box.
SCENES DURING RECORDING
Press the PAUSE/STILL button to
PAUSE
temporarily stop recording.
Press the PAUSE/STILL or
RECORD button to resume record-
ing.
SP
NOTES:
After five minutes, the TV/VCR will automatically
switch to the Recording mode to prevent tape dam-
age.
If “CLOSED CAPTION (ON)” is selected, the On-
Screen Display will appear for 5 seconds, then dis-
appear.
•
2 Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
•
- 20 -
EN
9I03
Avoid over lap of programs ...
There is a chance that a program will not be record-
ed. when programs overlap;
3 Begin OTR
OTR(2 : 30)
Press the REC/OTR button on the
TV/VCR as many times as needed.
The recording length will be deter-
mined by the number of times you
press the REC/OTR button. Each
The program with an earlier start has priority.
Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
•
•
SP
additional push will increase the recording time by
30 minutes. It is set up to 8 hours.
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
Push(es) Display
1 push
Recording length
(normal recording)
2 pushes
3 pushes
0:30
1:00
30 minutes
60 minutes
9:00AM
10:00AM
11:00AM
12:00PM
*Recording period is SHADED
17 pushes
8:00
480 minutes
The illustration below demonstrates the sequence
of recordings.
•
1 Select “TIMER PROGRAM-
TIMER RECORDING
– M E N U –
B
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
MING”
You may set the TV/VCR to start and end a record-
ing while you are away. You can set 8 programs to
record on specific days, daily or weekly within a 1
year period.
In the example below, the timer is being set to record:
July 6th, 2001
SETTING TIME: from 7:30PM to 8:50PM
Press the MENU button on the
remote control.
Confirm “TIMER PROGRAM-
MING” is pointed by pressing the PLAY/K button.
And press the F.FWD/B button.
If you have not yet set the clock, “MANUAL
CLOCK SET” appears. If so, fol-
low stops [3] to [8] on page 15.
Then set the timer recording.
ZERO RETURN
TIME SEARCH
DATE:
•
– TIMER PROGRAMMING –
CHANNEL:
TAPE SPEED:
CH61
SP
CH DATE
BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
B
Make sure ...
If a cable box or satellite box is connected with the
TV/VCR you will be limited to record only one
channel. And the channel selector on the TV/VCR
must be selected to the output channel of the boxes
CH 3 or CH 4 and then the actual channel to be
recorded must be selected on the boxes.
Clock must be set to the correct time and date
before setting the timer.
•
2 Select your desired program
position (1~8)
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the PLAY/K or STOP/L but-
ton to select the desired program
position.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
B
•
Then, press the F.FWD/B button.
TV/VCR power must be turn on to program it.
Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
•
•
3 Set the channel number
Press the PLAY/K or STOP/L button until the
desired channel number appears.
(Example: CH61)
The channel you want to record is properly set in
advance.
•
Then, press the F.FWD/B button.
Remember: If the TV/VCR is con-
– TIMER PROGRAMMING –
nected to a cable box or satellite
box, the TV/VCR must be on CH3
or CH4, then the channel to be
recorded is selected on the cable
box or satellite box.
CH DATE
BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 7/06 FRI -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
B
– TIMER PROGRAMMING –
CH DATE BEGIN END
4 Select once, every day or
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 EVRY DAY -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
weekly recording
For once recording :
B
- 21 -
EN
9I03
Press the PLAY/K (up) button until the desired
date appears. (Example: “7/06” for July 6th).
Then, press the F.FWD/B button.
10 Finish setting the program
Press the F.FWD/B or REW/s button. The program
is now completed.
For every day recording : To record a TV program at
the same time on the same channel every day.
To set another program, repeat steps [2] to [10].
Press the MENU button on the remote control to
return to original mode.
•
•
(Example: Monday through Sunday)
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the STOP/L (down) button
until “EVRY DAY” appears.
Then, press the F.FWD/B but-
ton.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 EVRY MON -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
B
11 Set the timer
Press the POWER button to set automatic timer
recording. The TIMER REC indicator lights up.
For weekly recording : To record a TV program at
the same time on the same channel every week.
(Example: every Monday)
You must turn off the TV/VCR to activate automat-
ic timer recording.
If power is not turned off and you continue watch-
ing TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
•
Press the STOP/L (down) button until “EVRY”
and your desired day of the week appear together.
Then, press the F.FWD/B button.
– TIMER PROGRAMMING –
5 Set beginning hour
TIMER PROGRAM EXTENSION
CH DATE
BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Press the PLAY/K or STOP/L but-
ton until the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then, press the F.FWD/B button.
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
61 7/06 FRI 7:12P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
2)Repeat step [1] on page 21.
3)Press the RECORD button and select the desired
program using the PLAY/K or STOP/L button.
4)Press the RECORD button again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the
– TIMER PROGRAMMING –
CH DATE BEGIN END
6 Set beginning minute
Press the PLAY/K or STOP/L but-
ton until the desired minute appears.
(Example: “30” for 7:30PM)
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/06 FRI 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
Then, press the F.FWD/B button.
7 Set end hour
– TIMER PROGRAMMING –
CH DATE BEGIN END
PAUSE/STILL button on the remote control. The
recording time returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automati-
cally be set to the SLP mode.
Press the PLAY/K or STOP/L but-
ton until the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the F.FWD/B button.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:30PM - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/06 FRI 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
5)Press the F.FWD/B or REW/s button to exit the
setting menu. Then press the MENU button on the
remote control to return to original mode.
– TIMER PROGRAMMING –
CH DATE BEGIN END
8 Set end minute
Press the PLAY/K or STOP/L but-
ton until the desired minute appears.
(Example: “50” for 8:50PM)
Then, press the F.FWD/B button.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50PM- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/06 FRI 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
TO CORRECT A PROGRAM
While setting a program; press the REW/s but-
ton to go back one step and enter the correct num-
•
9 Set the tape speed
Press the PLAY/K or STOP/L but-
ton until the desired tape speed
appears. (Example: SP)
– TIMER PROGRAMMING –
CH DATE BEGIN END
bers using the PLAY/K or STOP/L button.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50PMSP
-:- - - -
-:- - - -
-:- - - -
-:- - - -
After setting a program;
1)Press the POWER button.
•
61 7/06 FRI 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
2)Repeat steps [1] - [2] on page 21.
3)Press the F.FWD/B button (or press the REW/s
button to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the PLAY/K or STOP/L but-
ton.
4)Press the POWER button to set automatic timer
recording.
- 22 -
EN
9I03
TO CANCEL AN AUTOMATIC TIMER
RECORDING
USER’S SET UP
–
–
2 Set “AUTO RETURN” to [ON]
Press the PLAY/K or STOP/L but-
ton to point to “AUTO RETURN”.
Press the F.FWD/B or REW/s
button until [ON] appears.
RENTAL
REPEAT PLAY
AUTO RETURN
[OFF]
[OFF]
[ON]
After setting a program;
1)Press the POWER button.
•
B
2)Repeat steps [1] ~ [2] on page 21 and select a
program you want to cancel.
3)Press the T-PROG. CLEAR button.
4)Press the MENU button on the remote control to
return to TV mode.
While recording is in progress;
1)Press POWER button.
3 Auto Return will begin
When all the timer recordings are completed, the
TV/VCR will rewind to the beginning of the recorded
program(s).
NOTE:
If you press the POWER button while tape is
rewinding, the Auto Return will stop.
•
2)Press the STOP/EJECT button on the TV/VCR.
•
TO CHECK THE BEGIN/END TIME
1)Press the POWER button so that the REC indicator
goes off.
2)Press the MENU button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the F.FWD/B button. The details of pro-
grams appear on the TV screen.
4 Watch the recorded program
Press the PLAY button.
TO CANCEL THE AUTO RETURN
MODE
5)Press the MENU button on the remote control to
return to TV mode.
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
HINTS FOR AUTOMATIC
TIMER RECORDING
WAKE UP TIMER
Make sure the channel you want to record is prop-
erly set in advance.
It is not necessary to press the RECORD button for
timer recording.
Recording begins automatically at the Start time.
If you are recording using a Timer mode, you may
not operate the unit manually.
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
If the erase-prevention tab is removed, the cassette
will be ejected when the POWER button is pressed
to off.
•
The Wake Up Timer function turns on the TV/VCR
without using the POWER button after a desired
period of time.
•
•
•
NOTES:
Use the remote control for this procedure.
Clock must be set to the correct time before setting
•
•
•
the timer.
If you want to select [TAPE], you must insert a
cassette tape in the TV/VCR. The tape will start
playback automatically on your desired time.
•
•
If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediate-
ly, and the tape will be ejected.
•
1 Select “WAKE UP TIMER”
Press the WAKE UP/SLEEP button
on the remote control once, and
confirm “ON/OFF” is pointed.
AUTO RETURN
WAKE UP B ON/OFF
[ON]
TIMER
TV/TAPE
TIME
[TV]
Press the F.FWD/B or REW/s
[12:00AM]
button until [ON] appears.
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
2 Select “TV” or “TAPE”
Press the PLAY/K or STOP/L but-
ton until to point to “TV/TAPE”.
Press the F.FWD/B or REW/s
button, and select [TV] or [TAPE].
– M E N U –
1 Select “USER’S SET UP”
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press the MENU button on the
WAKE UP
TIMER
ON/OFF
B TV/TAPE
TIME
[ON]
B
remote control.
[TV]
[12:00AM]
Press the PLAY/K or STOP/L but-
ton to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
- 23 -
EN
9I03
3 Set wake up time
1 Select “SLEEP TIMER”
Press the WAKE UP/SLEEP button on the remote
control until “SLEEP TIMER” appears.
Press the PLAY/K or STOP/L but-
ton until to point to “TIME”.
Press the F.FWD/B or REW/s
button until your desired wake up
time appears.
WAKE UP
TIMER
ON/OFF
[ON]
2 Set sleep time
Press the PLAY/K, STOP/L,
F.FWD/B or REW/s button until
your desired sleep time appears.
TV/TAPE
[TV]
B TIME
[12:00AM]
Each additional push will increase (or decrease) the
time by 10 minutes.
SLEEP TIMER [2:00]
Each additional push will increase
4 Exit the Wake Up Timer setting
Press the MENU button on the remote control to
return to TV mode.
the time by 30 minutes up to 120 minutes.
Press the MENU button on the remote control to exit
the Sleep Timer setting.
TO CANCEL THE WAKE UP TIMER
TO CANCEL THE SLEEP TIMER
Repeat step [1] but select [OFF].
Press the WAKE UP/SLEEP button on the remote
control until “SLEEP TIMER” appears.
To view the time left for sleep timer press the WAKE
UP/SLEEP button twice, then press the MENU but-
ton on the remote control to exit the sleep timer set-
ting.
SLEEP TIMER
The Sleep Timer function turns off the TV/VCR
without using the POWER button after a desired
period of time.
NOTE:
This function does not operate during Recording
mode.
•
COPYING A VIDEO TAPE
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
You can make copies of video tapes made by friends
or relatives for your enjoyment.
2)Insert a blank video cassette, or one you want to
record over, into the TV/VCR’s cassette compart-
ment.
3)Press the SPEED button on remote control for the
TV/VCR to select the desired recording speed
(SP/SLP).
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
Connect your TV/VCR and a Source (Playing) VCR
using the following diagram.
4)Press the CHANNEL K or L button on the
TV/VCR until “AUX” appears on the screen.
5)Press the RECORD button on the TV/VCR.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
[Fig.8]
AUDIO
VIDEO
[The TV/VCR]
NOTE: For best results during dubbing, use the
TV/VCR’s front panel controls whenever possible.
The remote control might affect the source (Playing)
VCR’s playback operation.
[Ex: Source (playing)
VCR or camcorder]
Audio/Video
adapter cable
(not supplied)
VIDEO
OUT
IN
AUDIO
- 24 -
EN
9I03
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
WHEN THE CLOSED CAPTION MODE IS OFF:
<Off mode>
<Counter mode>
<Clock mode>
Counter mode: After 5 seconds, only
the counter remains. To clear it, press
the DISPLAY button.
Clock mode: After 5 seconds, only
the clock and the channel number
remain. To clear them, press the DIS-
PLAY button.
•
•
5:40PM
CH2
Press
once
Press
once
COUNT 0:12:34
Press once
ON:
OFF mode
Clock/Counter mode
WHEN THE CLOSED CAPTION MODE IS
•
•
The On Screen Display disappear after 5 seconds.
STOP
5:40 PM
CH2
This is true even if the MUTE button is pressed, or the
PAUSE/STILL button is pressed while recording.
SP
COUNT 0:12:34
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time
will not change on a blank tape or blank portions on
the tape.)The “–” indication will appear when the
tape has rewound further than “0:00:00” on the tape
counter.
When the end of a tape is reached during record-
ing, playback, or fast-forward, the tape will auto-
matically rewind to the beginning. After rewinding
finishes, the TV/VCR will eject the tape and turn
itself to off.
This function is operative when Repeat Play is set
to the [OFF] position.
•
•
•
The tape will not auto-rewind during timer record-
ing or One Touch Recording.
MAINTENANCE
back, the video heads in your TV/VCR may need
to be cleaned.
CABINET CLEANING
Wipe the front panel and other exterior surfaces of
the TV/VCR with a soft cloth immersed in luke-
warm water and wrung dry.
•
1.Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2.If a Video Head Cleaner does not solve the prob-
lem, please call our help line at 1-800-242-7158, to
locate an Authorized Service Center.
NOTES:
Remember to read the instructions included with
the video head cleaner before use.
Clean video heads only when problems occur.
Never use a solvent or alcohol. Do not spray insec-
•
ticide liquid near the TV/VCR. Such chemicals
may cause damage and discoloration to the
exposed surfaces.
•
AUTO HEAD CLEANING
•
Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
•
SERVICING
Should your TV/VCR become inoperative, do not
try to correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord, and please call our help line at 1-800-
242-7158, to locate an Authorized Service Center.
Playback picture may become blurred of interrupt-
•
•
ed while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use, or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during play-
- 25 -
EN
9I03
TROUBLESHOOTING GUIDE
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to
remedy the problem.
PROBLEM
CORRECTIVE ACTION
Make sure the AC cord is connected to an AC outlet.
Make sure the power is turned on.
Make sure the AC cord is connected to an AC outlet.
Check antenna connection.
Let the TV/VCR program its’ tuner memory.
Adjust direction or replace antenna.
Adjust picture controls.
Adjust volume control on remote control or main unit.
Press the MUTE button to restore sound.
Make sure the timer recording is set correctly.
Make sure the power is off.
Make sure the TV/VCR clock is set correctly.
Make sure the tape has an erase-prevention tab. If need, cover the
hole with plastic tape.
No power.
•
•
•
•
•
No picture and sound.
No picture or poor picture on
TV/VCR.
No sound or poor sound.
•
•
•
•
•
•
•
Timer recording is not possible.
Cannot go into Record mode.
•
•
Playback picture is partially noisy.
Adjust tracking control for a better picture using the CHANNEL
or L button on the TV/VCR.
Head cleaning may be necessary. Refer to “AUTO HEAD
CLEANING” on page 25.
K
•
•
No picture but the audio is OK in
playback.
•
•
No operation by infrared Remote
Control.
Video or color fades in and out
Make sure the AC cord is connected to an AC outlet.
Check batteries in remote control.
You can not copy a copyrighted video tape. You are experiencing
copy guard protection.
•
•
•
when making a copy of a video tape
.
•
CLOSED CAPTION PROBLEM
My TV/VCR is showing captions
that are misspelled.
POSSIBLE REMEDY
• You are watching a live broadcast and spelling errors made by the
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue
in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies
what is being said.
• can display a dialogue to a maximum of 220 words per minute. If a
• dialogue exceeds that rate, selective editing is used to insure that the
• captions remain up-to-date with the current TV screen dialogue.
• Interference caused by building, power lines, thunderstorms, etc.
• may cause scrambled or incomplete captions to appear.
My captions are scrambled with
white boxes on the TV screen.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed
as being closed captioned but none • up the actual program so that additional advertising time can be
of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating
show any captions. The tape box • company accidentally left out the captioning signals during the
mentions it being closed captioned. • copying process.
My TV screen shows a black box
on certain channels.
• You are in the TEXT mode. Select CAPTION mode to CAPTION
• [OFF].
- 26 -
EN
9I03
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
CRT :
13 or 19 inch in-line gun, 90˚
deflection tube
NTSC-M
Video input level :
Audio input level :
0.5~2.0Vp-p
-15dBs
Television system :
Closed caption system :§15.119/FCC
Video S/N ratio : More than 46dB
Audio S/N ratio : More than 43dB
Video Heads :
Tape width :
Tape speed
SP :
LP :
SLP :
Tuner channel
TV VHF Low :
TV VHF High :
TV UHF :
CATV
Rotary two-head
1/2 inch
OTHER SPECIFICATIONS
[ 13 inch model ]
Power requirement : AC 120V/60Hz
Power consumption : 65W
33.40mm/sec.
16.67mm/sec.
11.12mm/sec.
Dimensions :
H:15-3/4” (400mm)
W:15-3/16” (386mm)
D:14-13/16” (377mm)
24.3 lbs (11kg)
#2~#6
#7~#13
#14~#69
Weight :
[ 19 inch model ]
Power requirement : AC 120V/60Hz
Power consumption : 90W
VHF :
5A
MID band :
SUPER band :
HYPER band :
Terminals
A5~A1, A~I
J~W
W+1~W+84
Dimensions :
H:19-11/16” (500mm)
W:19-7/16” (494mm)
D:18-5/16” (465mm)
44.1 lbs (20kg)
Weight :
Antenna input :
VHF/UHF 75 ohms
unbalanced
RCA connector [ 1
RCA connector [ 1
1/8” monaural (3.5 mm)
Designs and specifications are subject to change
without notice and without our legal obligation.
If there is a discrepancy between languages, the
default language will be English.
•
•
Video input :
Audio input :
Earphone :
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
TV Display
5A
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
A
B
14
15
CATV channel
TV Display
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CATV channel
R
S
T
U
V
W
W+1
37
W+2
38
W+3
39
W+4
40
W+5
41
W+6
42
W+7
43
W+8
44
W+9
45
TV Display
31
32
33
34
35
36
CATV channel
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display
CATV channel
TV Display
CATV channel
TV Display
76
77
78
79
80
81
82
83
84
85
W+59 W+60 W+61 W+62 W+63 W+64
100 101 102 103 104 105
86
87
88
89
90
W+55 W+56 W+57 W+58
A-5
95
A-4
96
A-3
97
A-2
98
A-1
99
CATV channel
TV Display
91
92
93
94
CATV channel
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
TV Display
106
W+80 W+81 W+82 W+83 W+84
121 122 123 124 125
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CATV channel
TV Display
- 27 -
EN
9I03
CONTROLES DE OPERACIÓN Y SUS FUNCIONES
Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exac-
tamente la misma. En este manual se muestra el modelo de 19".
NOTA:
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del
mando a distancia universal.
POWER
AUDIO
VIDEO
STOP/EJECT
REW
PLAY
F.FWD
CHANNEL
VOLUME
REC/OTR
EARPHONE
1
2 3 4 5 6 7 891011 12 13 14
Botón de expulsión (EJECT)–Púlselo en el modo
de parada para expulsar la cinta del
televisor/videograbadora.
Botón L–
Púlselo para seleccionar los modos de ajuste desde el
menúde la pantalla.
Púlselo para introducir dígitos cuando establezca un
programa.
25
4
WAKE-UP
POWER
/SLEEP
EJECT
•
•
13
15
CHANNEL
RETURN
1
4
7
2
5
8
3
6
9
24
(Por ejemplo: Para ajustar el reloj o establecer un pro-
grama de temporizador)
5 Botón de rebobinado (REW)– Púlselo para rebobi-
nar la cinta, o para ver la imagen en retroceso rápido
durante el modo de reproducción. (Búsqueda con
rebobinado)
CHANNEL
VOLUME
11
0
+100
MENU
DISPLAY
MUTE
12
16
17
5
Botón s–
23
6
Púlselo para seleccionar un modo desde un menúpar-
ticular.
(Por ejemplo: IDIOMA o ADJUST DE USER)
6 Botón de reproducción (PLAY)– Púlselo para ini-
PLAY
•
7
REW
F.FWD
STOP
4
SPEED PAUSE/STILL
RECORD
ciar la reproducción.
Botón K–
Púlselo para seleccionar los modos de ajuste desde el
•
menúde la pantalla.
Púlselo para introducir dígitos cuando establezca un
programa.
22
21
8
18
T-PROG.
CLEAR
GAME
TIME SEARCH
COUNTER
RESET
19
20
•
(Por ejemplo: Para ajustar el reloj o establecer un pro-
grama de temporizador)
7 Botón de avance rápido (F.FWD)– Púlselo para
avanzar rápidamente la cinta, o para ver la imagen en
avance rápido durante el modo de reproducción.
(Búsqueda con avance rápido)
1 Toma de auriculares (EARPHONE)– Para conec-
tar los auriculares (no suministrados) y escuchar en pri-
vado. La toma es mono y tiene un tamaño de 3,5 mm.
Botón B–
2 Toma de entrada de audio (AUDIO)– Conéctela a
la toma de salida de audio de su equipo de audio,
videocámara u otra videograbadora.
3 Toma de entrada de vídeo (VIDEO)– Conéctela a
la toma de salida de vídeo de su videocámara u otra
videograbadora.
Cuando establezca un programa (por ejemplo: para
ajustar el reloj o para establecer un programa de tem-
porizador), púlselo para determinar su elección y vaya
al paso siguiente que quiera introducir.
Púlselo para determinar los modos de ajuste desde el
menúde la pantalla.
•
•
•
4 Botón de parada (STOP)– Púlselo para detener la
cinta.
Púlselo para seleccionar un modo desde un menúpar-
- 28 -
ES
ticular.
Botón de reposición del contador (COUNTER
RESET)– Púlselo para reponer el contador a 0:00:00.
(Por ejemplo: IDIOMA o ADJUST DE USER)
20 Botón de juego (GAME)– Establece el modo del
8 Botón de grabación (REC)– Púlselo para iniciar la
grabación manual.
juego y el modo de entrada externa al mismo tiempo.
21 Botón de búsqueda con tiempo (TIME
SEARCH)– Púlselo para activar el modo de búsqueda
con tiempo.
Botón de grabación de un toque (OTR)– Activa
la grabación de un toque. (Sólo en el
televisor/videograbadora)
22 Botón de pausa/imagen fija (PAUSE/STILL)–
Púlselo para detener temporalmente la cinta durante la
grabación o para ver una imagen fija durante la repro-
ducción.
9 Indicador de grabación (RECORD)– Parpadea
durante la grabación.
Se enciende en el modo de espera de la grabación con
temporizador.
10 Ventanilla sensora del mando a distancia–
Recibe las señales infrarrojas procedentes del mando a
distancia.
11 Botones de canales (CHANNEL K/ L)– Púlselos
para seleccionar los canales deseados para ver o
grabar.
23 Botón de silenciamiento (MUTE)– Silencia el
sonido. Púlselo de nuevo para recuperar el sonido.
24 Botón de retorno de canal (CHANNEL
RETURN)– Púlselo para volver al canal anterior. Por
ejemplo, pulsando una vez este botón, la visualización
del canal cambiará de 3 (canal actual) a 10 (canal ante-
rior), y al pulsarlo por segunda vez, el canal cambiará
del 10 al 3.
25 Botón del temporizador despertador/para
dormir (WAKE UP/SLEEP)– Ajusta el tempo-
rizador para despertarse/dormir.
Se puede mostrar el menú principal en la pantalla del
televisor pulsando repetidamente este botón del televi-
sor/videograbadora.
Función de seguimiento– Pulse los botones para
minimizar el ruido de vídeo (líneas o puntos en la pan-
talla) durante la reproducción.
26 Cordón de alimentación– Conéctelo a la toma de
CA estándar (120V/60Hz).
27 Terminal de antena (ANT.)– Para conectar una
12 Botones de volumen (VOLUME X / Y)– Ajustan
el nivel del volumen.
antena o sistema de televisión por cable.
13 Botón de la alimentación (POWER)– Púlselo
para encender y apagar el televisor/videograbadora.
Púlselo para activar la grabación con temporizador.
14 Compartimiento del videocasete
15 Botones numerados– Púlselos para seleccionar los
canales deseados para ver o grabar. Para seleccionar
canales del 1 al 9, pulse primero el botón 0 y luego el
botón 1 a 9.
Botón +100– Cuando seleccione canales de tele-
visión por cable cuyo número sea superior al 99, pulse
primero este botón, y luego pulse los dos últimos dígi-
tos. (Para seleccionar el canal 125, pulse primero el
botón “+100” y luego el “2” y el “5”.)
16 Botón de menú (MENU)– Púlselo para visualizar el
menúprincipal en la pantalla del televisor.
17 Botón del visualizador (DISPLAY)– Visualiza el
contador o el número del canal actual y la hora actual
en la pantalla del televisor.
18 Botón de velocidad de cinta (SPEED)– Púlselo
para elegir la velocidad de grabación deseada: SP/SLP.
19 Botón T-PROG. CLEAR– Púlselo para cancelar un
programa de temporizador.
- 29 -
ES
CONEXIONES DE ANTENA/CABLE
Desde el cable coaxil o
caja de emisiones vía
satélite de 75 ohm del
sistema de Cable
Caja de CATV
o caja de emi-
siones vía satélite
(no incluído)
Antena combinada de
VHF/UHF
(no incluído)
Antena de varilla UHF/VHF
(incluído para solamente 13”)
OUT
IN
Antena VHF
(no incluído)
Desde el
sistema de Cable
Antena UHF
(no incluído)
ANT.
Combinador de
VHF/UHF
(no incluído)
ANT.
Cable coaxil
de 75 ohm (no incluído)
PARA GRABAR UN CANAL
CODIFICADO/DESCODIFICADO
ANTENA COMBINADA DE VHF/UHF
La antena de varilla de VHF/UHF (incluído para solamente
13”) es desmontable. Inserte el vástago de la antena en el
agujero de la parte trasera superior del
1. Ajuste el selector de canales del televisor/videograbado-
ra al canal de salida del convertidor de televisión por
cable o del convertidor de emisiones vía satélite. (Ej.:
CA3)
2. Seleccione el canal que desee grabar de su convertidor
de televisión por cable o del convertidor de emisiones
vía satélite.
televisor/videograbadora.
Conecte la varilla de antena de VHF/UHF o la antena com-
binada de VHF/UHF al terminal ANT. del
televisor/videograbadora.
ANTENAS SEPARADAS DE VHF/UHF
En algunos lugares será necesario utilizar una antena exte-
rior.
MODO DE ENTRADA EXTERNA
Cuando utilice una señal de entrada externa (otra
videograbadora o una videocámara), conecte los cables de
salida de audio/vídeo del equipo de reproducción a las
tomas AUDIO IN/VIDEO IN de su
televisor/videograbadora. Y luego pulse el botón CHAN-
NEL K o L hasta que “AUX” aparezca en la pantalla.
CABLE SIN CONVERTIDOR/DESCODIFICADOR
Utilice esta conexión si su sistema de televisión por cable
se conecta directamente a su televisor/videograbadora sin
convertidor.Utilizando esta conexión usted podrá:
1)Utilizar el mando a distancia del televisor/videograbado-
ra para seleccionar canales.
Usted puede programar el temporizador para que explore
todos los canales que puedan recibirse en su zona.
2)Programar uno o más canales sin codificar para realizar
la grabación automática con temporizador.
NOTA: Con esta unidad SÓLO se podrá grabar y ver un
mismo canal al mismo tiempo.
INSTALACIÓN DE LAS PILAS
CABLE CON CONVERTIDOR/DESCODIFICADOR
O CONVERTIDOR DE EMISIONES VÍA SATÉLITE
1)Abra la tapa del compartimiento de las pilas del mando
a distancia presionándola en el sentido de la flecha.
Si su servicio de televisión por cable le suministra un con-
vertidor, o si usted utiliza un sistema de emisiones vía
satélite, usted podrá utilizar las conexiones básicas
mostradas aquí.
2)Inserte 2 pilas tamaño “AA” en el compartimiento de las
pilas, en el sentido indicado por las marcas de polaridad
(+/-).
3)Vuelva a poner la tapa.
Utilizando estas conexiones, usted también podrá grabar
canales codificados. Sin embargo, la selección de los
canales deberá hacerse con el convertidor de televisión por
cable con el convertidor de emisiones vía satélite. Esto sig-
nifica que los canales no podrán ser cambiados con el
mando a distancia del televisor/videograbadora. La
grabación inatendida se limita a un canal cada vez.
- 30 -
ES
PREPARACIÓN DE CANALES POR
PRIMERA VEZ
1) Enchufe el cable de alimentación del
AJUSTE DEL RELOJ
Cerciórese...
La alimentación del televisor/videograbadora deberá
estar conectada.
En el ejemplo de abajo, el reloj va a ajustarse así:
FECHA: 1 de mayo de 2000
HORA: 5:40 PM
1) Pulse el botón MENU en el mando a distancia.
Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE RELOJ”.
Luego, pulse el botón F.FWD/B.
2) Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE MANUAL RELOJ”.
Luego, pulse el botón F.FWD/B.
3) Pulse el botón PLAY/K o STOP/L hasta que aparezca
el mes deseado. (Ejemplo: Mayo - 05)
Luego, pulse el botón F.FWD/B.
4) Pulse el botón PLAY/K o STOP/L hasta que aparezca
el día del mes deseado. (Ejemplo: 1 - 01)
•
televisor/videograbadora en una toma de CA estándar.
NOTA: Si aparezcan algunos digitos en el rincón de la
pantalla, pulse el botón POWER sin desenchufar el cable
de alimentación.
2) Pulse el botón POWER para encender el
televisor/videograbadora.
3) Seleccione “ENGLISH” o “ESPAÑOL” utilizando el
botón F.FWD/B o REW/s. “[ ]” indica el idioma
seleccionado.
4) Pulse el botón PLAY/K o STOP/L para señalar
“AUTOPRESELECCION”.
Luego pulse el botón F.FWD/B. El sintonizador explo-
rará y memorizará todos los canales activos de su área.
NOTAS:
El televisor/videograbadora distingue entre los canales
de televisión estándar y los canales de televisor por
cable.
•
Luego, pulse el botón F.FWD/B.
5) Pulse el botón PLAY/K o STOP/L hasta que aparezca
el año deseado. (Ejemplo: 2000)
Luego, pulse el botón F.FWD/B.
6) Pulse el botón PLAY/K o STOP/L hasta que aparezca
la hora deseada. (Ejemplo: 5, PM)
Luego, pulse el botón F.FWD/B.
7) Pulse el botón PLAY/K o STOP/L hasta que aparezca
Si desea reproducir o grabar una cinta ANTES de prea-
justar el sintonizador, usted tendrá que pulsar el botón
MENU en el mando a distancia. Para preajustar de
nuevo el sintonizador, consulte “REPETICIÓN DE LA
PREPARACIÓN DE CANALES”.
La unidad de televisor/videograbadora puede reconocer
los canales de TV como ellos de TV por cable a causa
de los condiciones de recepción. En este caso, pruebe el
preajuste automático de nuevo en los condiciones finas
de recepción.
5) El sintonizador se para en el canal memorizado más
bajo. Si desea recuperar canales seleccionados, usted
podrá seleccionar directamente el canal deseado con los
botones numerados del mando a distancia o con los
botones CHANNEL K o L.
•
•
el minuto deseado. (Ejemplo: 40)
8) Pulse el botón MENU en el mando a distancia. Aunque
los segundos no se visualizan, éstos empiezan a contar
desde 00 cuando se pulsa MENU en el mando a distan-
cia. Utilice esta función para sincronizar el reloj con la
hora correcta.
- 31 -
ES
FUNAI CORPORATION
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original
retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail
purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be
required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was
attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not apply to any product not pur-
chased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage
which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage
which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commer-
cial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MER-
CHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRE-
SENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.
WHEN YOU ARE RETURNING THE PRODUCT FOR SERVICE TO THE FACTORY SERVICE CENTER, PLEASE CON-
TACT THE FUNAI SERVICE DEPARTMENT TO RECEIVE A R.A. (REPAIR AUTHORIZATION) NUMBER PRIOR TO
SHIPPING. ANY POSTAGE, INSURANCE AND SHIPPING COST, INCURRED IN PRESENTING OR SENDING YOUR
FUNAI/SYMPHONIC PRODUCT FOR SERVICE ARE SHIPPER’S RESPONSIBILITY.
CAREFULLY PACK WITH PROPER PACKING MATERIALS, PREFERABLY IN THE ORIGINAL CARTON AND IF NEEDED
DOUBLE BOX IT.
ATTACH WRITTEN DOCUMENTATION DETAILING THE COMPLAINT, TO THE OUTSIDE OR INSIDE OF THE CAR-
TON.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF
PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.
To locate your nearest FUNAI Authorized Service Center or for general service procedure, please call 1-800-242-7158 or write to
the following:
FUNAI CORPORATION
Factory Service Center
100 North Street; Teterboro, NJ 07608
Tel :1-800-242-7158
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
0EMN01752
|
Sharp Blu ray Player BD AMS10U User Manual
Sharp Blu ray Player BD HP90S User Manual
Sony Camera Lens NEX 3C User Manual
Sony Cassette Player TC TX77 User Manual
Sony CD Player cdr w33 User Manual
Sony Graphics Tablet SGPT11 User Manual
Sony Home Theater System DAV DX155 User Manual
Southbend Convection Oven 536A User Manual
Spirit Treadmill ET10 User Manual
Tanita Scale HD 340 User Manual